Enwork Grid Frame Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 14

background image

26. Re-attach Fin wall top caps making sure tiles seat in grooves of top cap. Using #15 Torque drive

install 4 - #8-32 screws (UZSCREWALZ without thread cutting).

Worksurfaces and Supports

1. Mount legs to tops as specified in floor plan in preparation for attachment to Grid Frame.
2. If worksurfaces are ped supported then place peds into position per floor plan.
3. If attaching work surfaces to Grid, Tether Brackets (UMTB or UMTD) will need to be

attached to Spine wall as shown below.

UMTB Tether Bracket are used for tall legs (power/data above worksurface) – see above.

UMTD Tether Brackets are used for short legs (power/data below worksurface) – see above.

«
...
8
9
10
11
12
...
»

Содержание Grid Frame















Отзывы:

Нет отзывов

Похожие инструкции для Grid Frame

Бренд: MAJA Möbel Страницы: 16

Бренд: J&K Страницы: 9

Бренд: J D Williams Страницы: 8

Бренд: J&K Страницы: 7

Бренд: namesake Страницы: 38

Бренд: Yaasa Страницы: 18

HAYMONT FRS80952T-ST2

Бренд: HAMPTON BAY Страницы: 9

Бренд: Cooper Lighting Страницы: 3

Бренд: studioduc Страницы: 26

Safco Flaunt 3456

Бренд: LDI Spaces Страницы: 3

TECHNI MOBILI RTA-4804L

Бренд: RTA Страницы: 28

Бренд: tepro Страницы: 26

Бренд: Eagle Group Страницы: 2

Бренд: Target Страницы: 20

PALADIN 0777201

Бренд: XROCKER Страницы: 10

Бренд: WASAGUN Страницы: 42

Бренд: Walker Edison Страницы: 16

Бренд: Next Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды