Environmental Express Oakton 300 Series Скачать руководство пользователя страница 56

Страница: 56 / 62

Error message

E2100

Sensor ADC error

The ADC system of Sensor
has a problem.

Remove the batteries,
disconnect the AC power
supply, and then press the
power key.

E2101

Sensor memory

error

The memory system of
Sensor has a problem.

E22XX

Sensor

communication

error

The communication system
of Sensor has a problem.

Disconnect the sensor
connector from meter, and then
reconnect the sensor connector
to the meter. Or, contact your
dealer for repair.

E2250

Sensor update

request error

Sensor update did not
complete successfully.

Execute sensor update again.

E2251

Sensor update

error

Error occurred during
sensor update.

E2300

Calibration

interval alarm

error

Exceeds the calibration
interval setup.

Calibrate the meter.

E2301

CAL error:

Offset

The offset potential of the
pH sensor is out of the
range of ±50 mV.

Maintenance the sensor or use
the new standard solution.

E2302

CAL error:

Slope

The slope of sensor is out
of range.

E2303

CAL error:

CAL points

Maximum calibration points
exceeded.

Up to maximum calibration
points.

E2304

CAL error:

Unknown solution

The meter cannot
recognize the standard
solution.

(1) Make sure to place the

sensor in the standard
solution.

(2) Make sure the buffer group

setting.

(3) Clean the sensor.
(4) Replace the new sensor.

E2305

CAL error:

Cell constant

Cell constant is out of
range.

(1) Make sure to place the

sensor in the standard
solution.

(2) Make sure the buffer group

setting.

(3) Clean the sensor.
(4) Replace the new sensor.

E2306

CAL error:

Temp. CAL

Temperature set for
calibration is more than
±2°C.

Make sure to place the sensor in
the standard solution.

E2308

CAL error:

Membrane

DO membrane has reached
the lifetime.

Replace with a new sensor cap.

Error

code

Error

description

Cause of error

Recommended Action

www.calcert.com

[email protected]

1.800.544.2843

Содержание Oakton 300 Series































































Результаты поиска

Содержание Oakton 300 Series

Отзывы:

Бренды по названию

Популярные бренды

Environmental Express Oakton 300 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Oakton 300 Series

Отзывы:

Бренды по названию

Популярные бренды