Enviro EG31 Nova Скачать руководство пользователя страница 7

Operating Instructions

For Your Safety, Read Safety Precautions And 

Lighting Instructions Before Operating

L

ighting

 i

nstRuctions

:

Figure 3: Gas Valve.

Figure 4: Pilot Burning.

1.   STOP! Read the safety information above on this label.
2.   Turn off all electrical power to this appliance.
3.   Turn off the gas control knob clockwise            to the off position.
4.   Open door. Wait fIve (5) minutes to clear out any gas. Close door. If
      you smell gas STOP! Follow  “B” in the  above safety information. If
      you do not smell gas go to the next step.
5.   Find pilot-located to the left under the front log. Turn the gas control
      knob counter-clockwise

      to “PILOT”. Push the gas control in fully

      and hold, keep knob depressed for about 30 seconds after 
      the pilot is lit. Release knob. If pilot goes out, repeat 
      steps 4 through 5.

CAUTION:

Hot while operating. Do not touch, severe burns may result. Keep children, clothing, 
furniture, gasoline or other  flammable vapors away.

FOR YOUR SAFETY READ BEFORE OPERATING

WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING

 PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. 

 A)  This appliance is equipped with a pilot, which must be lit by hand by
       following these instructions exactly. 
 B)  BEFORE LIGHTING smell all around the appliance area for gas and next to
       the floor because some gas is heavier than air and  will settle on the floor.    
   WHAT TO DO IF YOU SMELL GAS: 
       Do not try to light any appliance. Do not touch any electrical switch: do not
       use any phone in your building. Immediately call your gas supplier from a
       neighbor's phone. Follow  the gas suppliers instructions. If you cannot reach
       your gas supplier, call the fire department.

C)   Use only your hand to push in or turn the gas control knob; 
       NEVER use tools. If the knob will not push in or turn by hand, do 
       not try to repair it. Call a qualified service technician. Force or 
       attempted repair may result in a fire or explosion.
D)   Do not use this appliance if any part has been under water.
       Immediately call a qualified service technician to inspect the
       appliance and to replace any part of the control system and any
       gas control which has been under water.     

LIGHTING INSTRUCTIONS

 WARNING: this gas valve has a lockout device, which will not allow  the
    pilot burner to be relit until the thermocouple has cooled. If the knob does
    not pop up when released, stop and immediately call your service
    technician or gas supplier.
    If  the pilot does not stay lit after several tries, turn the gas control knob  
    to “OFF” and call your service technician or gas supplier.    
6.   Turn the gas control knob counter clockwise            to the  “ON”
      position. Flip the burner switch to “ON” THEN TURN THE “HI/LOW”
      knob to the desired setting.
7.   Turn on the electrical power to the unit.

TO TURN OFF GAS TO APPLIANCE

1. Flip burner switch to “OFF”
2. Turn the gas control knob clockwise             to the “OFF” position.

C-10489

3. Turn off all electrical power to the appliance if service is to be performed.

CAUTION:

 Do not operate this fireplace with the glass removed, cracked or broken. Replacement of the panel(s) should be done by a licensed or 

qualified person! This appliance needs fresh air for safe operation and must be installed with provisions for  combustion and ventilation air. See 
installation and operating instructions manual.  Keep burner and control compartment clean.

WARNING: 

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage, or loss of life. Refer to owner's 

information manual provided with this appliance. For assistance or additional information consult a qualified installer, service agency or the gas supplier.
See installation and operating instructions accompanying appliance. Installation and service must be performed by a qualified installer, service agency, 
or the gas supplier.

O

L I

T

P

T

P

 T
H

      TP

   

   

 T

H

IN               

OUT

H

I

L

O

N

OF

O

F

LI

P

T

O

WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY A FIRE OR EXPLOSION MAY 

RESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY OF LOSS OF LIFE.

Figure 2.  Lighting Instruction Label

7

Содержание EG31 Nova





































Отзывы: