Enviro C-10450 Скачать руководство пользователя страница 15

Страница: 15 / 33

Initial Installation

QUALIFIED INSTALLERS ONLY

ATHEDRAL

EILING

NSTALLATION

Figure 19: Cathedral Ceiling Support Box

Leveling.

Figure 20: Cathedral Ceiling Support Box

Installation.

STEP 1.

Follow installation steps 1 & 2 under ‘Vertical Installation’.

STEP 2.

Using the plumb bob, mark the centerline of the venting

system on the ceiling and drill a small hole through the

ceiling and roof at this point. From the roof, locate the drill

hole and mark the outline of the “Cathedral Ceiling Support

Box”.

STEP 3.

Remove shingles or other roof coverings as necessary to

cut the rectangular hole for the “Support Box”. Cut the hole

1⁄8” larger than the “Support Box” outline.

STEP 4.

Lower the “Support Box” through the hole in the roof

until the bottom of the “Support Box” protrudes at least 2

inches (5 cm) below the ceiling. Align the “Support Box”

both vertically and horizontally with a level as shown in

Figure 19. Temporarily tack the “Support Box” in the place

through the inside walls and into the roof sheathing.

STEP 5.

Using tin snips, cut the “Support Box” from the top corners

down to the roof line, and fold the resulting flaps over the

roof sheathing (Figure 20). Before nailing it in to the roof,

run a bead of non-hardening mastic around the top edges

of the “Support Box”, to make a seal between the box and

the roof. Clean out any combustible material from the

inside of the “Support Box”.

STEP 6.

Complete the cathedral ceiling installation by following the

same procedures outlined in Steps 4 through 9 for “Vertical

Installation”.

REESTANDING

IRECT

ENT

ITH

OUPLER

KIT COMPONENTS:

Quantity Description

Horizontal direct vent termination cap

Ø65⁄8” (17 cm) 90° elbow

Flue collar adapters (only one used)

Wire spacers

T-20 Torx screws

Decorative rings

Wall thimble

4 oz tube RTV silicone

Inside finish trim collar

” tech screws

5’ (190 cm) length of Ø4” (10 cm) double walled flex pipe

11⁄2” wood screws

24” (61 cm) section of Ø65⁄8” (17 cm) straight pipe

Vinyl siding deflector

Please ensure that all components are supplied with this kit. If components are missing or have been damaged,

contact your dealer, distributor, or courier company. Do not attempt the installation if components are missing or

damaged.

Содержание C-10450


































Результаты поиска

Содержание C-10450

Отзывы:

Похожие инструкции для C-10450

Бренды по названию

Популярные бренды

Enviro C-10450, Руководство пользователя

Результаты поиска

Содержание C-10450

Отзывы:

Похожие инструкции для C-10450

Бренды по названию

Популярные бренды