manualshive.com logo in svg

Enttec OCTO MK2, Руководство пользователя

Поделиться
Скачать
Enttec OCTO MK2 Скачать руководство пользователя страница 10

OCTO MK2 (71521) 

Visit the ENTTEC website for the latest version. 

.. 

 

USER MANUAL  

10

 |

 

ID: 5928937 

Document Updated: Jan 2022 

 

  

 

Home 

The Home tab displays the following information:

 

 

DHCP status – (either enabled / 

disabled).

 

 

IP address.

 

 

Netmask.

 

 

Gateway.

 

 

Mac Address.

 

 

Link Speed.

 

 

Node Name.

 

 

Firmware version on device.

 

 

System uptime.

 

 

Input protocol set on device.

 

 

Output LED protocol set on device. 

 

 

Personality.

 

 

Settings 

 The Settings page allows a user to do the following:

 

 

Change a device name for identification.

 

 

Enable/disable DHCP.

 

 

Specify static network settings.

 

 

Set the output LED Protocol.

 

 

Set the number of mapped pixels.

 

 

Configure how colors are mapped to pixels 

through the Pixel Order function.

 

 

Reset to factory defaults.

 

 

Reboot the device.

 

 

 

 

 

 

 

 

 

 

 

Содержание OCTO MK2























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды