iv
European Waste Electrical and Electronic Equipment (WEEE) Notice
In
accordance
with
Directive
2002/96/EC
of
the
European
Parliament
on
waste
electrical
and
electronic
equipment
(WEEE):
1.
The
symbol
above
indicates
that
separate
collection
of
electrical
and
electronic
equipment
is
required
and
that
this
product
was
placed
on
the
European
market
after
August
13,
2005,
the
date
of
enforcement
for
Directive
2002/96/EC.
2.
When
this
product
has
reached
the
end
of
its
serviceable
life,
it
cannot
be
disposed
of
as
unsorted
municipal
waste.
It
must
be
collected
and
treated
separately.
3.
It
has
been
determined
by
the
European
Parliament
that
there
are
potential
negative
effects
on
the
environment
and
human
health
as
a
result
of
the
presence
of
hazardous
substances
in
electrical
and
electronic
equipment.
4.
It
is
the
users’
responsibility
to
utilize
the
available
collection
system
to
ensure
WEEE
is
properly
treated.
For
information
about
the
available
collection
system,
please
go
to
http://www.enterasys.com/support/
or
contact
Enterasys
Customer
Support
at
353
61
705586
(Ireland).
Safety Information
Class 1 Laser Transceivers
The single mode interface modules use Class 1 laser transceivers.
Read the following safety information before installing or operating these modules.
The
Class
1
laser
transceivers
use
an
optical
feedback
loop
to
maintain
Class
1
operation
limits.
This
control
loop
eliminates
the
need
for
maintenance
checks
or
adjustments.
The
output
is
factory
set,
and
does
not
allow
any
user
adjustment.
Class
1
Laser
transceivers
comply
with
the
following
safety
standards:
• 21
CFR
1040.10
and
1040.11
U.S.
Department
of
Health
and
Human
Services
(FDA).
• IEC
Publication
825
(International
Electrotechnical
Commission).
• CENELEC
EN
60825
(European
Committee
for
Electrotechnical
Standardization).
When
operating
within
their
performance
limitations,
laser
transceiver
output
meets
the
Class
1
accessible
emission
limit
of
all
three
standards.
Class
1
levels
of
laser
radiation
are
not
considered
hazardous.
When
the
connector
is
in
place,
all
laser
radiation
remains
within
the
fiber.
The
maximum
amount
of
radiant
power
exiting
the
fiber
(under
normal
conditions)
is
‐
12.6
dBm
or
55
x
10
‐
6
watts.
Removing
the
optical
connector
from
the
transceiver
allows
laser
radiation
to
emit
directly
from
the
optical
port.
The
maximum
radiance
from
the
optical
port
(under
worst
case
conditions)
is
0.8
W
cm
‐
2
or
8
x
10
3
W
m
2
sr
‐
1.
Do
not
use
optical
instruments
to
view
the
laser
output.
The
use
of
optical
instruments
to
view
laser
output
increases
eye
hazard.
When
viewing
the
output
optical
port,
power
must
be
removed
from
the
network
adapter.
Содержание SecureStack C2 C2G170-24
