Connecting to the Network
SecureStack B2 Installation Guide 3-25
Connecting Fiber-Optic Cables to MT-RJ Ports
This
section
contains
the
procedures
for
connecting
a
1000BASE
‐
SX
multimode
fiber
‐
optic
segment
from
the
network
or
other
devices
to
an
MT
‐
RJ
port
connector
in
a
Mini
‐
GBIC
(MGBIC
‐
MT01).
Each
fiber
‐
optic
link
consists
of
two
fiber
‐
optic
strands
within
the
cable:
•
Transmit
(TX)
•
Receive
(RX)
The
transmit
strand
from
a
device
port
connects
to
the
receive
port
of
a
fiber
‐
optic
Gigabit
Ethernet
device
at
the
other
end
of
the
segment.
The
receive
strand
of
the
applicable
MT
‐
RJ
port
connects
to
the
transmit
port
of
the
fiber
‐
optic
Gigabit
Ethernet
device.
Enterasys Networks
recommends
labeling
fiber
‐
optic
cables
to
indicate
receive
and
transmit
ends.
Many
cables
are
pre
‐
labeled,
providing
matching
labels
or
tapes
at
both
ends
of
each
strand
of
cable.
To
connect
an
MT
‐
RJ
cable
to
a
fixed
MT
‐
RJ
connector
of
a
Mini
‐
GBIC,
refer
to
Figure 3
‐
20
and
proceed
as
follows:
1.
Remove
the
protective
covers
(not
shown)
from
the
front
panel
MT
‐
RJ
fiber
‐
optic
port
(port
46
in
this
example)
and
from
the
connectors
on
each
end
of
the
cable.
Warning:
Do not use optical instruments to view laser output. The use of optical
instruments to view laser output increases eye hazard.
Advertencia:
No utilizar instrumentos opticos para ver el laser. El uso de instrumentos
opticos para ver el laser incrementa el riesgo de perdida de la vision.
Warnhinweis:
Benutzen sie keinesfalls optische Hilfmittel, um die Funktion des Lasers zu
überprüfen, es könnte ihr Augenlicht gefährden.
Note:
Leave the protective covers in place when the connectors are not in use to prevent
contamination.
Caution:
Do not touch the ends of the fiber-optic strands, and do not let the ends come in
contact with dust, dirt, or other contaminants. Contamination of cable ends causes
problems in data transmissions. If the ends of the fiber-optic strands become
contaminated, use a canned duster to blow the surfaces clean. A fiber-port cleaning swab
saturated with optical-grade isopropyl alcohol may also be used to clean the ends.
Precaución:
No toque los extremos de los cables de fibra óptica y evite su contacto con el
polvo, la suciedad o con cualquier otro contaminante. Si los extremos de los cables se
ensucian, es posible que la transmisión de datos se vea afectada. Si nota que los
extremos de los cables de fibra óptica se ensucian, utilice aire comprimido para limpiarlos.
También puede limpiarlos con un estropajo embebido en alcohol isopropílico.
Содержание SecureStack B2 B2G124-48P
