background image

 

 

 

CUSTOMER RELEASE NOTES

 

 

1/21/09  P/N: 9038177-27 

Subject to Change Without Notice 

Page: 20

 

of 28 

 
F0615-O 

 

 

Firmware Release 7.0.4.3: 

Using the auto-ap feature does not allow load-balancing on individual radios.  

Description 

 When using the auto-ap feature, it is not possible to set all of the AP attributes. 

Per AP load-balancing control is not supported on auto-ap. The system global settings for 
load-balancing apply to all auto-aps. 

Workaround 

— 

If you must configure a load-balance group for a specific AP, configure the AP as 

a regular AP. 
Using telnet over a WAN link may affect the telnet session.  

Description 

 When using telnet to manage a RAS over a high-latency WAN link, it is possible 

for the telnet session to stop responding.  

Workaround 

 Restart the telnet session. 

Auto-aps do not behave correctly on cluster seed when the maximum number of APs is 
configured.  

Description 

 When a cluster seed RAS boots an auto-ap, it checks the seed configuration on the RAS to 

determine if the cluster can support any additional APs. If the system is already configured 
with the maximum number of APs allowed, new auto-aps do not operate correctly. 

Workaround 

 Reduce the number of configured APs in the cluster configuration. 

Voice handsets can be sensitive to changes on an in-service SSID.  

Description 

 Particular voice handsets are sensitive to changes made to an in-service SSID. 

This can result in the handset operating with stale connection information. 

Workaround 

 When using affected handsets, disable the Service Profile prior to making any 

configuration changes. 
The time and date do not synchronize with an NTP server, if the NTP client on the RAS 
is enabled before the NTP service is started on the server. 

 

Firmware Release 7.0.3.7: 
Description 

 If you reload a switch configuration with cluster mode turned on, RASM cannot determine which 

RoamAbout switch is the active seed in the cluster configuration. (53952) 

Workaround 

 Disable cluster mode and then re-enable it. Normal operation resumes on the network. 

Using the auto-ap feature does not allow load-balancing on individual radios. (53331) 

Description 

 When using the auto-ap feature, it is not possible to set all of the AP attributes. Per AP load-

balancing control is not supported on auto-ap. The system global settings for load-balancing applies to all auto-
aps. (53331) 

Workaround 

 If you must configure a load-balance group for a specific AP, configure the AP as a regular AP. 

Using telnet over a WAN link may affect the telnet session. (52853) 

Description 

 When using telnet to manage a RoamAbout switch over a high-latency WAN link, it is possible 

for the telnet session to stop responding. (52853) 

Workaround 

 Restart the telnet session. 

Auto-aps do not behave correctly on cluster seed when the maximum number of APs is configured. (52633) 

Description 

 When a cluster seed RoamAbout switch boots an auto-ap, it checks the seed configuration on 

the RoamAbout switch to determine if the cluster can support any additional APs. If the system is already 
configured with the maximum number of APs allowed, new auto-aps do not operate correctly. 

Workaround 

 Reduce the number of configured APs in the cluster configuration. 

CAPWAP data plane UDP port changed from 5001 to 5247. (53029) 

Description 

 The UDP port for CAPWAP data packets has changed from 5001 to 5247 to comply with the 

updated CAPWAP specification. You may experience problems with roaming VLANs between RoamAbout 
switches with MSS Version 7.0 and RoamAbout switches with earlier versions of MSS. 

Workaround 

 If your network configuration requires tunnled VLANs, be sure that all RoamAbout switches on 

the network are configured with the same version of MSS. 
Using the active-scan feature triggers packet loss on legacy APs with older Intel wireless adaptors. (50901) 

Description 

 When using active-scan on legacy APs with the Intel 2915 wireless adaptor, a station may 

experience some level of packet loss. (50901) 

Workaround 

 Disable active-scan on any legacy APs supporting older Intel clients. 

Содержание RBT-8500 RoamAbout





























Отзывы: