Quick Start User Guide
V2.6
HT
Series
HT500
|
HT700
|
HT800
|
HT900
|
HT446
INTRODUCTION
The HT series is a professional range of commercial grade portables
designed and manufactured to meet IP68 specification for total protection
against water and dust intrusion.
To meet your exact requirements, the radio may have been customised by
your Entel authorised dealer. These features will be explained in a separate
guide issued by the dealer.
PACKING LIST
HTxxx Radio
CSAHT
Rapid charger (not supplied with HTxx5 & HTxx6)
CNBxxx
Rechargeable Li-Ion battery
CBHxxx
Spring loaded belt clip
CATxxx
High efficiency antenna
OPTIONAL ACCESSORIES
Attaching and removing accessories
To attach an accessory, remove the accessory cover by unscrewing the locking
screw anti-clockwise (leave cover attached or store in a safe place).
Plug the accessory into the socket, then carefully
tighten the locking screw clockwise until finger tight
(do not over tighten or use any implement).
To remove an accessory, unscrew the locking
screw of the accessory by hand in an anti-clockwise
direction.
Ensure you re-fit the accessory socket cover (the
radio is not submersible without the socket covered).
BATTERY INFORMATION
Battery charging
1.
Connect the AC adapter to the charger pod and plug in.
2.
Turn the radio off.
3.
Insert the battery pack into the charger pod, either with or without the radio
attached. The charger LED status light changes to red and charging begins.
4.
When charging is complete the charger LED status changes from red
to green. A fully discharged battery pack will take approximately 3 hours to
recharge.
A flashing red LED on the charger indicates there is a problem with the
battery. Remove the battery from the charger and consult your Entel Dealer.
CAUTION
BATTERY PACK PRECAUTIONS
•
Do not recharge the battery pack if it is already fully charged. Doing so may
reduce the life of the battery pack.
•
After charging is complete, remove the battery from the charger. If the power
to the charger is turned off and on again, charging will restart and the battery
will become overcharged.
•
Please ensure that the radio is turned off before placing it in the charger and
never switch a radio on whilst in the charger.
•
Only use Entel branded battery packs and chargers.
•
Do not short the battery terminals or dispose of the battery in a fire.
•
Do not charge the radio and/or battery pack if they are wet.
DANGER
DO NOT DISASSEMBLE OR MODIFY THE BATTERY IN ANY WAY!
Your Entel battery pack incorporates a safety circuit to avoid danger, if the safety
circuit is damaged or bypassed, or the battery cells are damaged directly, they
may generate extreme heat, smoke, rupture and emit flames.
Above approvals apply to specific models only
CONTROLS & INDICATORS
1.
On/Off button: press and hold to turn the radio on or off.
2.
Volume control
3.
Channel control
4.
Push To Talk (PTT) button: press to speak and release to listen.
5.
Dealer programmable button (ask your dealer for more information)
6.
Dealer programmable Soft Key (long press only)
7.
LED indicator
Red steady
- Transmitting
Red flashing slowly
- Battery needs recharging
Green steady
- Receiving
Amber steady
- Invalid signal being received
Amber flashing rapidly
- Scanning
Amber pulsing
- In standby mode
8.
Keypad buttons
9.
Microphone
4
4
4
4
5
5
5
5
5
5
5
5
5
1
1
1
1
8
3
2
2
2
NON DISPLAY
3 KEY LCD
8 KEY LCD
20 KEY LCD
2
3
3
3
7
7
7
7
9
Ta
l
k H
ere
9
Ta
l
k H
ere
9
Ta
l
k H
ere
9
Ta
l
k H
ere
6
6
5
5
5
PREPARING YOUR RADIO FOR USE
Attaching/removing the antenna
Attaching/removing the battery pack
1.
To attach, carefully align the antenna with
the socket. Screw in the antenna clockwise
(taking care not to cross the thread) until it
is seated firmly with the accessory cover’s
rubber ring between the antenna and the top
of the radio
(A)
.
2.
To remove, unscrew the antenna
anti-clockwise
(B)
.
1.
To attach, locate the pegs on the bottom of the
battery into the slots on the radio and press
the top of the battery against the radio. Secure
battery by tightening the screw clockwise
by hand. (Do not use any implement or over
tighten)
(C)
.
To remove, unscrew the locking screw
anti-clockwise and pull the battery away
from the top of the radio
(D)
.
A
B
C
SWITCHING ON, RECEPTION
AND SWITCHING OFF
1.
To switch on, press and hold the on/off button
(1) on the front of the radio.
2.
When the radio has passed its diagnostic tests,
it will emit a fanfare tone.
3.
The radio will enter standby mode. This is
indicated by the LED Amber flashing once
every 5 seconds, signaling that the radio is
ready for use.
4.
Adjust the volume control to select the desired
volume level.
5.
Using the channel buttons, ensure you have
the correct channel selected.
6.
When receiving a valid signal, the LED will
illuminate steady green and audio will be
emitted from the radio’s speaker or audio
accessory (if attached).
7.
When finished using the radio, switch off
by pressing and holding the on/off button
(1) until the radio beeps and the LED/LCD is
extinguished.
TRANSMITTING
1.
Perform steps 1 through to 5 above.
2.
Before transmitting, monitor the channel and
make sure it is clear.
3.
When receiving a signal, wait until the signal
stops before transmitting. The radio cannot
transmit and receive simultaneously.
4.
Press the Push To Talk (PTT) button (4) to begin
your transmission. To confirm transmission the
LED will illuminate red.
5.
For best transmitted speech quality, you must
talk directly into the radio’s microphone (9) at
around 4cm between your mouth and the radio.
6.
Please note: if you talk into the top of the
radio or with your mouth further away, you will
transmit poor quality speech.
7.
When the transmission is finished release the
PTT button.
EU DECLARATION OF CONFORMITY
Hereby, Entel UK Limited of:
320 Centennial Ave, Centennial Park,
Elstree, WD6 3TJ, United Kingdom:
Declares that the radio equipment type
HT446, HT500 series, HT700 V2 series,
HT800 V2 series, HT900 V2 series,
HT800 V2 series and HT900 V2 series
is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is
available at the following internet address:
www.entel.co.uk/red
This declaration is valid for Directive 2014/34/EU
HT800 V2 Series, HT900 V2 Series, HT500 Series
EN 60079- 0:2012
EN 60079-11:2012
Related certificates:
HT800 V2 Series, HT900 V2 Series
Sira 10ATEX2066X
HT9XX marking Ex ll 2G Ex ib llC T4 Gb
HT8XX marking Ex ll 2G Ex ib llA T4 Gb
HT500 Series
IECEx SIR 10.0097X
HT5XX marking Ex II 2G Ex ib IIA T4 Gb
Sira Certification. Unit 6, Hawarden Industrial
Park, Hawarden, Deeside. CH5 3US, UK
Notified Body No. 0518
Quality Assurance Notification:
Intertek. Intertek House, Leatherhead
KT22 7SB, UK
Notified Body No. 0359
Name: Mike Jamieson
Position: Quality Manager
Date: 1st May 2017
Signed:
www.entel.co.uk
D
A
ll R
ig
ht
s R
es
er
ve
d. C
op
yr
ig
ht E
nt
el U
K L
td
.
