enphase M215-60-2LL-S22 Скачать руководство пользователя страница 19

Страница: 19 / 42

M215 Installation and Operation



141-00012 Rev 06

Step 6: Ground the Microinverters (if required)

This step is required only for M215-60-2LL-S22, S23, and S24. It is not required for M215-60-2LL-
S22-IG, S23-IG, or S24-IG.

Each

M215-60-2LL-S22, S23, and S24

comes with a grounding cleat (wire connector) that can

accommodate a 6-8 AWG GEC (grounding electrode conductor). Check local requirements for allowable
grounding conductor sizes.

NOTE

: Ground the system in accordance with all applicable local electrical codes and the

National Electrical Code (NEC), ANSI/NFPA 70.

NOTE

: CSA has evaluated and approved the Wiley E

lectronics “WEEB” grounding

washers for use with the Enphase Microinverter. Compatible grounding washer part
numbers and installation guidelines are included in the

Racking Compatibility List

NOTE

: The AC output neutral is not bonded to ground inside the microinverter.

Route a continuous GEC through each of the microinverters to the NEC-approved AC
grounding electrode.

You can ground the PV racking and PV module to this conductor using a listed wire
connector approved for the purpose.

Torque the 10/32 grounding cleat screw to 2 N m (20 to 25 in-lbs). Do not over torque.

NOTE

: Using a power screwdriver to tighten the grounding clamp screw is not

recommended due to the risk of thread galling.

Содержание M215-60-2LL-S22








































Результаты поиска

Содержание M215-60-2LL-S22

Отзывы:

Похожие инструкции для M215-60-2LL-S22

Бренды по названию

Популярные бренды

enphase M215-60-2LL-S22, Инструкция по установке и эксплуатации

Результаты поиска

Содержание M215-60-2LL-S22

Отзывы:

Похожие инструкции для M215-60-2LL-S22

Бренды по названию

Популярные бренды