enphase Envoy-S Скачать руководство пользователя страница 8

Страница: 8 / 32

AC Combiner Box Installation

Enphase Installer

Toolkit mobile app

Pre-installation Checks

Review the following pre-installation checks before you install the AC Combiner Box.

Plan the Internet Connection

To use the

Enlighten

web-based monitoring and analysis software, additional requirements are:

•

Internet connection for the Envoy-S through a traditional router or modem or Enphase Mobile

Connect (Enphase model CELLMODEM-01). Decide whether to connect the Envoy-S to the

Internet using integrated Wi-Fi, an Enphase Mobile Connect modem, or using Ethernet cable with

or without a power line communication (PLC) bridge.

•

One of the following Web browsers with cookies enabled: Chrome 5 or higher, Firefox 11 or

higher, Internet Explorer (IE) 9 or higher, or Safari 5 or higher

Download the Installer Toolkit

The Enphase Installer Toolkit is a mobile app for iOS and Android devices that allows

installers to configure the system while onsite, eliminating the need for a laptop and

improving installation efficiency.

•

Download the Enphase Installer Toolkit mobile app and open it to log in to

your Enlighten account. With this app, you can connect to the Envoy to

track system installation progress. To download, go to

enphase.com/installer-toolkit

or scan the QR code:

•

To run the Installer Toolkit app, you need either of the

following mobile devices:

−

An Android mobile device running Android version

4.2 or later, or

−

An iOS device running iOS 7.0 or later, specifically an iPhone 4 or later

or an iPod Touch 5th generation

Box Contents

Check the shipping box for the following items:

•

Enphase AC Combiner Box with Envoy-S

•

Ferrite bead to attach to your Ethernet Cable, if used

•

The

Enphase AC Combiner Box Quick Install Guide

Required Items

•

Tools, including screw driver, pliers, torque wrench, etc.

•

Overcurrent protection in accordance with NFPA 70-2014, §705.12(D)

•

Suitable mounting hardware: use screws that are long enough to secure the unit to the vertical

mounting surface

•

75°C or 90°C copper conductors, rated for wet locations

•

UL listed rain-tight or wet location hubs for wire entry into the enclosure

Optional Items

Make sure you have the following optional items, if needed:

•

Two consumption metering split-core CTs (order two CTs: Enphase CT-200-SPLIT)

141-00030 Rev 02

Содержание Envoy-S

































Результаты поиска

Содержание Envoy-S

Отзывы:

Похожие инструкции для Envoy-S

Бренды по названию

Популярные бренды

enphase Envoy-S, Руководство по установке

Результаты поиска

Содержание Envoy-S

Отзывы:

Похожие инструкции для Envoy-S

Бренды по названию

Популярные бренды