enphase Envoy-S Скачать руководство пользователя страница 19

Страница: 19 / 32

AC Combiner Box Installation

11. Connect to Enlighten

The Envoy-S requires a connection to the Internet for reporting to Enlighten. You can provide this connection

through an existing broadband router, other Wi-Fi access point at the installation site, or by using the

Enphase Mobile Connect cellular modem.

WARNING

Risk of Equipment Damage. Do not remove power from the Envoy-S if the LEDs are

flashing green. This indicates that a software upgrade is in progress.

Connect to a broadband router using one of these methods, described in the following sections:

•

Method A: Integrated Wi-Fi

•

Method B: Enphase Mobile Connect (order CELLMODEM-01 separately)

•

Method C: Ethernet cable (not included, installer must provide). This method requires that you use

the ferrite bead included with the AC Combiner Box.

•

Method D: Power Line Communication Bridges (order EPLC-01 separately). This method requires

that you use the ferrite bead included with the AC Combiner Box.

Method A: Integrated Wi-Fi

To use the Enphase integrated Wi-Fi, you need a wireless

router. To use Wi-Fi:

On the Envoy-S, verify that no Ethernet cable is plugged

into the RJ45 port.

If your router supports WPS, press and hold the WPS

button on the wireless router for a few seconds. On most routers, a WPS LED begins flashing.

If you are using the Installer Toolkit mobile app, tap the

Network

button, tap

Wi-Fi

, and then tap your

network from the list of available networks. If the wireless router does not support WPS, you may be

prompted to enter a password.
If you are not using the Installer Toolkit mobile app, you can only connect using WPS. Initiate a WPS

connection by pressing and holding the

AP Mode

button for 5 seconds.

The Network Communications LED

begins flashing green. Within three minutes the Network

Communications LED

lights solid green, indicating a successful connection to the Internet and to

Enlighten. If the Network Communications LED

does not light solid green, see “Internet Connection

Issues” on page 27.

Method B: Enphase Mobile Connect

(Order CELLMODEM-01 separately)

To install Enphase Mobile Connect:

Connect the antenna to the connector (marked

CELL

) on the modem.

Mount the modem as described in the

Enphase Mobile Connect Installation

Guide

Connect the USB cable:

•

First, connect the USB cable to the USB port(s) on the Envoy-S.

•

Then, connect the mini-USB connector to the Mobile Connect modem.

If receiving power from the Envoy-S, the modem power LED lights.
Within three minutes the Network Communications LED

lights solid green, indicating a

successful connection to the Internet and to Enlighten.

141-00030 Rev 02

Содержание Envoy-S

































Результаты поиска

Содержание Envoy-S

Отзывы:

Похожие инструкции для Envoy-S

Бренды по названию

Популярные бренды

enphase Envoy-S, Руководство по установке

Результаты поиска

Содержание Envoy-S

Отзывы:

Похожие инструкции для Envoy-S

Бренды по названию

Популярные бренды