enphase Envoy-S Скачать руководство пользователя страница 25

Страница: 25 / 32

AC Combiner Box Installation

Envoy-S LED States

LED

State

Description

All

Flashing amber in unison

The Envoy-S is booting up

Flashing green sequentially

Software upgrade in progress

Network

Communications

Solid green

Communicating with Enlighten

Flashing green

WPS connection in progress, or Envoy-S is attempting to

connect to Enlighten

Solid amber

Local network connection only

Off

No network connection

AP mode

Solid green

AP mode enabled:
Envoy Wi-Fi network available

Off

AP mode disabled:
Envoy Wi-Fi network unavailable

Power

production

Solid green

All communicating microinverters are producing

Flashing green

Microinverter upgrade in progress

Solid Amber

At least one microinverter is not producing

Off

Microinverters are not communicating
(low light or night time)

Device

Communications

Solid Green

All microinverters are communicating

Flashing Green

Device scan in progress

Solid Amber

At least one microinverter is not communicating

Off

Microinverters are not communicating
(low light or night time)

Microinverter Detection Issues

Troubleshoot power line communication issues as follows.

Issue: Device Communications LED is Solid Amber

If the Device Communications LED lights solid amber, it may be a result of low light levels. If there is not

enough sunlight to power up the microinverters, they cannot communicate with the Envoy. If there is

sufficient daylight for the microinverters to power up, the issue may be that the Envoy is having difficulty

communicating over the power lines. To troubleshoot this issue:

•

Check the Installer Toolkit mobile app to see which microinverters are not communicating.

•

Check that the circuit breaker(s) for the PV array are in the “ON” position.

•

Verify that the PV modules are connected to the microinverters.

•

Verify the PV module DC voltage is within the allowable range for the microinverter.

Issue: Installer Toolkit Detects Fewer Microinverters than Expected

The

Microinverters detected

count is an indication of the number of online microinverters producing power,

reporting in to the Envoy, and not having any error conditions. If this number is lower than expected, it may

indicate that the Envoy is not done scanning/discovering the entire array. Alternatively, it may indicate that

the Envoy is having difficulty communicating over the power lines. It could also be a result of low light levels

or that the PV module voltage is too low for the microinverter to power up. To troubleshoot the issue:

141-00030 Rev 02

Содержание Envoy-S

































Результаты поиска

Содержание Envoy-S

Отзывы:

Похожие инструкции для Envoy-S

Бренды по названию

Популярные бренды

enphase Envoy-S, Руководство по установке

Результаты поиска

Содержание Envoy-S

Отзывы:

Похожие инструкции для Envoy-S

Бренды по названию

Популярные бренды