manualshive.com logo in svg

enphase D380, Руководство по устранению неисправностей

Поделиться
Скачать
enphase D380 Скачать руководство пользователя страница 43

Troubleshooting an Enphase System 

 

 2014 Enphase Energy Inc. 

August 2014 

43 

Microinverter Failed to Report 

A microinverter that reports a 

Microinverter Failed to Report

 condition is unable to communicate with 

the Envoy over the AC power lines. Occasional instances of this error may be ignored as microinverter 
communications will likely recover on the next reporting cycle.  

 

Verify that the site has service from the electrical utility and that no solar circuit-breaker has 
tripped. 

 

If communications do not recover right away (the Envoy polls the microinverters every five 
minutes), make sure that the Envoy is plugged in very near to the circuit breaker panel. Also, if 
other devices are sharing the electrical outlet with the Envoy, remove those devices to improve 
communication signal strength.  

 

If the Envoy was recently relocated, or if new devices or appliances were added to the circuit, the 
new location may not be suitable for power line communications. You may need to relocate the 
Envoy to improve signal strength and reduce interfering noise on the power lines. 

 

If several microinverters are reporting this condition, you may need to relocate the Envoy to 
another electrical outlet to improve communication signal strength.  

For further troubleshooting steps, see 

“

Microinverters are not detected, or, power line communication 

level is low or poor

”

 on page 22.  

 

Over Temperature 

See 

“

Critical Temperature

” 

on page 37.  

 

Zigbee Device Failed to Report 

If the Envoy is connected to an Environ thermostat, this condition may occur if there is an interruption in 
communication between the Environ thermostat and the Envoy.   

Make sure the Envoy ZigBee USB stick is plugged into the Envoy. Occasional instances of this error may 
be ignored, as a temporary interference to the radio signal may cause this condition and will recover on 
its own. If this condition persists, it may be necessary to add a ZigBee repeater to boost signal strength 
between ZigBee devices. 

See the 

Environ Smart Thermostat Installation and Operation Manual

 at 

http://www.enphase.com/support

 

for more information. 

 

Zigbee USB Stick Removed 

The Envoy Communication Gateway no longer detects the presence of the ZigBee USB stick. Make sure 
that the ZigBee USB stick is fully seated in the Envoy USB port. 

 

 

Содержание D380














































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды