manualshive.com logo in svg

enphase D380, Руководство по устранению неисправностей

Поделиться
Скачать
enphase D380 Скачать руководство пользователя страница 40

Troubleshooting an Enphase System 

 

 2014 Enphase Energy Inc. 

August 2014 

40 

 

DC Too High 

The microinverter reports that DC input voltage from the PV module is too high. 

 

If one microinverter reports 

DC Too High

 events, then the PV module may be incompatible. The 

PV module may generate a higher voltage than is recommended for the microinverter. Refer to 
the Module Compatibility Calculator at http://enphase.com/module-compatibility-calculator-m250-
update/ to check PV module compatibility 

 

If multiple units report 

DC Too High

, and you have ruled out incompatible PV modules, contact 

Enphase Customer Support to verify the firmware version of the microinverters. 

 

Device Produced No Power 

Device Produced No Power

 triggers when the microinverter produced 0 watts of power for more than 24 

hours.  

 

Verify that the site has service from the electrical utility and that none of the solar circuit-breakers 
are tripped. 

 

Check the system event history for 

AC Voltage Out Of Range

 and 

AC Frequency Out Of 

Range

. These events indicate possible problems with your utility service. 

 

Check the system event history for 

GFI Tripped

 or 

DC Resistance Low

. If the solar installer 

verifies that the connected PV module is working, this event can indicate that the microinverter 
needs to be replaced. 

 

Envoy not Reporting 

An Envoy not Reporting event is raised when the Internet connection is experiencing a problem. 

If the Envoy LCD displays 

–

Web

, then the Envoy is not currently communicating with the Enlighten 

servers. The Internet service may be down or the router may be unplugged or turned off.  

Internet connections often have temporary outages. If the situation persists, contact your ISP (Internet 
Service Provider). When the connection is restored, the Enphase Envoy communication gateway will 
transmit all the energy data that it stored. 

 

If the Internet service is dropping out periodically, and you notice that other devices at the site are 
also losing Internet connectivity, contact the ISP. 

 

Do you have dial-up Internet service? Dial-up Internet service is not supported on the Envoy. 

 

The Envoy may have an internal error; see 

“

Envoy Issues

” 

on page 11. 

 

 

See 

“

Did the Envoy previously have an Internet connection at this site?

”

 on page 15.  

 

Gateway Failure 

The Envoy has detected a software problem. To clear this message, unplug the Envoy from the electrical 
outlet and then plug it back in. Do this only once. If it returns to failure mode, contact Enphase Customer 
Support. 

 

Содержание D380














































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды