manualshive.com logo in svg

enphase D380, Руководство по устранению неисправностей

Поделиться
Скачать
enphase D380 Скачать руководство пользователя страница 37

Troubleshooting an Enphase System 

 

 2014 Enphase Energy Inc. 

August 2014 

37 

o

  A step-up transformer installed on site between the primary load center and the 

Enphase branch circuits can create ACVOOR conditions. 

 

 

 

If you checked and verified all of the previous conditions and 

ACVOOR

 nuisance tripping is 

still occurring, and neither the installer nor the utility can mitigate, Enphase can modify all of 
the microinverter grid profiles to allow for slightly expanded trip-points, while still remaining 
within spec.  

 

Critical Temperature 

A Critical Temperature condition is rare and occurs if the microinverter reports an internal temperature 
that exceeds the rated range. The microinverter reacts by producing less power to reduce internal 
temperature. Once the internal temperature of the microinverter diminishes, the microinverter resumes full 
power production and the error message clears. No action is required unless the condition persists. If it 
persists, contact Enphase Energy customer support. 

This reflects internal temperature coming from a sensor inside the microinverter, not the ambient 
temperature. For more information, see the Enphase Technical Brief on temperature at 

http://www.enphase.com/support

.

 

 

DC Resistance Low 

–

 Power Off 

A DC Resistance Low 

–

 Power Off event occurs only with the M250 Microinverter and some models of 

the M215 Microinverter and is indicated with a solid red status LED on the microinverter. The LED 
remains red and the Envoy continues to report the fault until the error clears.  

An insulation resistance (IR) sensor in the microinverter measures the resistance between positive and 
negative PV inputs to ground. If either resistance drops below a threshold, the microinverter stops power 
production and raises this event. This may indicate defective module insulation, defective wiring or 
connectors, moisture ingress, etc. Although the cause may be temporary, this microinverter condition 
persists until the sensor is manually reset. 

If a microinverter registers a DC Resistance Low condition, clear this condition through the Envoy 
Interface. An Envoy is required to send the 

clear-dc-resistance-low

 message to clear the condition. If 

the condition does not clear after you perform the following procedure, contact Enphase Energy customer 
support at 

[email protected]

. 

 

Содержание D380














































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды