enphase BRK-100A-2P-240V Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 12

enphase BRK-100A-2P-240V Скачать руководство пользователя страница 1

Q U I C K

I N S T A L L

G U I D E

Model number: EP200G101-M240US01

Install the Enphase

IQ System Controller 2

To install the Enphase

IQ System Controller 2 and the Enphase IQ System Controller 2 wall-mount bracket, read and follow all warnings and instructions in this

guide and in the

Enphase IQ System Controller 2 Installation and Operation Manual

at

enphase.com/support

. Safety warnings are listed on the back of this

guide. These instructions are not meant to be a complete explanation of how to design and install an energy storage system. All installations must comply with

national and local electrical codes and standards.

Only qualified electricians shall install, troubleshoot, or replace the IQ System Controller 2.

The Enphase Energy System includes the Enphase IQ System Controller 2 with Microgrid Interconnection Device (MID) capability, which

consolidates interconnection equipment into a single enclosure and streamlines grid-independent capabilities of PV and storage installations

by providing a consistent, pre-wired solution for residential applications. Along with MID functions, it includes PV, storage, and generator input

circuits.

©2021 Enphase Energy. All rights reserved. Enphase, the Enphase logo, IQ System Controller 2 , IQ Battery, IQ Gateway, IQ combiner, IQ microinverter, Enphase

App and other trademarks or service names are the trademarks of Enphase Energy, Inc. Data subject to change. Rev02-10-25-2021

Scenario 1:

Whole home backup with IQ System

Controller as service entrance:

This

is the preferred configuration for back

up of the entire main load panel. This

configuration supports up to an 80A

breaker each for the PV circuit, battery

storage and Generator(optional).

Scenario 2:

Partial home backup with main load

panel as service entrance:

This is

the preferred configuration for partial

home backup with subpanel with

PV and IQ Battery. Generator can be

integrated with IQ System Controller

based on the homeowner’s needs.

Scenario 3:

Whole home backup with Solar

Only backup:

This is the preferred

configuration for backup of the entire

main load panel using only IQ8 PV.

Generator can be integrated with

IQ System Controller based on the

homeowner’s needs.

(optional)

(optional)

(optional)

1
2
3
...
»

Содержание BRK-100A-2P-240V













Отзывы:

Нет отзывов