Enodis TEMPSTAR Скачать руководство пользователя страница 8

Страница: 8 / 99

Tempstar LT/NB/S/SDS Technical Manual 7610-011-86-35

Issued: 06-26-2006 Revised: N/A

SECTION 1: SPECIFICATION INFORMATION

OPERATING CAPACITIES

PERFORMANCE/CAPABILITIES

OPERATING CAPACITY:

RACKS PER HOUR

DISHES PER HOUR

1425

GLASSES PER HOUR

1425

OPERATING CYCLE (SECONDS):

WASH TIME

RINSE TIME

DWELL TIME

TOTAL CYCLE TIME

TANK CAPACITY:

WASH TANK (GAL)

8.0

WASH TANK (L)

30.3

RINSE TANK (TEMPSTAR/TEMPSTAR SDS) (GAL) 3.0
RINSE TANK (TEMPSTAR/TEMPSTAR SDS) (L)

11.4

STEAM REQUIREMENTS:

COIL SIZE

3/4”

STEAM FLOW PRESSURE (P.S.I.)

10-20

CONSUMPTION @ 15 P.S.I. (LBS/HR)

ELECTRICAL REQUIREMENTS

WASH MOTOR HP

3/4

NOTE: Always refer to the machine data plate for specific
electrical and water requirements. The material provided
on this page is for reference only and may be subject to
change without notice.

WATER REQUIREMENTS

TEMPSTAR/TEMPSTAR SDS:

WASH TEMPERATURE (MINIMUM)(°F)

150

WASH TEMPERATURE (MINIMUM)(°C)

RINSE TEMPERATURE (MINIMUM)(°F)

180

RINSE TEMPERATURE (MINIMUM)(°C)

INLET WATER TEMPERATURE:

12KW RINSE HEATER (°F)

140

12KW RINSE HEATER (°C)

14KW RINSE HEATER (°F)

110

14KW RINSE HEATER (°C)

FLOW PRESSURE (PSI)

WATER LINE SIZE (NPT)

3/4”

DRAIN LINE SIZE (NPT)

1 1/2”

TEMPSTAR LT:

WASH TEMPERATURE (MINIMUM)(°F)

130

WASH TEMPERATURE (MINIMUM)(°C)

RINSE TEMPERATURE (MINIMUM)(°F)

130

RINSE TEMPERATURE (MINIMUM)(°C)

INLET WATER TEMPERATURE (°F)

130

INLET WATER TEMPERATURE (°C)

FLOW PRESSURE (PSI)

WATER LINE SIZE (NPT)

3/4”

DRAIN LINE SIZE (NPT)

1 1/2”

MINIMUM CHLORINE REQUIRED (PPM)

TEMPSTAR NB/TEMPSTAR S:

WASH TEMPERATURE (MINIMUM)(°F)

150

WASH TEMPERATURE (MINIMUM)(°C)

RINSE TEMPERATURE (MINIMUM)(°F)

180

RINSE TEMPERATURE (MINIMUM)(°C)

INLET WATER TEMPERATURE (°F)

180

INLET WATER TEMPERATURE (°C)

FLOW PRESSURE (PSI)

WATER LINE SIZE (NPT)

3/4”

DRAIN LINE SIZE (NPT)

1 1/2”

Содержание TEMPSTAR




































































































Результаты поиска

Содержание TEMPSTAR

Отзывы:

Бренды по названию

Популярные бренды

Enodis TEMPSTAR, Техническое руководство

Результаты поиска

Содержание TEMPSTAR

Отзывы:

Бренды по названию

Популярные бренды