background image

 

 

The RCM modules are part of a powerful RF system solution from EnOcean for operation and 

control applications. Because the RF transmitters are self-powered (no batteries), 
maintenance-free RF systems can be implemented.  

 
The RCM modules operate together with the following further EnOcean components: PTM 

(batteryless radio switches), STM (batteryless radio sensors) and TCM (bi-directional radio 
modules) 

 

 
 
 

 

1.3 Features Overview 

Power Supply

: ........................................................................................ 5 V DC ± 5 % 

Current Input

: ............................................................ 29 mA max. (without output load) 

Receive Frequency

: ................................................ 868.3 MHz (stabilized by crystal PLL) 

Sensitivity / Channel Bandwidth

: ..................................................... -95 dBm / 280 kHz 

Control Inputs

: ................................... 6 inputs for set up of operating and learning modes 

Functional Outputs

: ......... 4 outputs, their function depends on the selected operation mode 

Learning Mode Output

: ................................................ indicates learning of transmitters

 

Number of RF transmitters learnable

:  ............................. up to 30 EnOcean transmitters  

Note: In serial mode all received EnOcean telegrams are transmitted  

RSSI Output

:.........................................................indicates received peak signal strength 

Direct Signal Output

: .................................................. physical layer 1 output (120 kbps) 

 

 
 

 

1.4 Physical Dimensions 

Antenna

:.................................. 9 cm whip antenna or external 50 Ohm antenna mountable  

Dimensions of PCB

: ........................................18.0 x 42.0 x 5.5 mm (without wiring pins) 

Connector

:  ........................................16 pins, grid 2.0 mm (4.0 mm in length,   0.5 mm) 

 

 

 
©EnOcean GmbH 

 

Page 5 of 20 

 

RCM 152 User Manual V1.31 

 

Содержание RCM 152





















Отзывы: