manualshive.com logo in svg

Eno Scientific Well Watch 700, Руководство пользователя

Поделиться
Скачать
Eno Scientific Well Watch 700 Скачать руководство пользователя страница 7

CAUTIONS

The Well Watch 710 Controller is not water proof! 

The controller is designed to be housed in a weather proof shelter. A gasketed 
enclosure or well shelter are desired.

Sudden application of well pressure may damage the probe!  

The 730 Probe was designed to be used on wells under pressure up to 100 psi. 
However, when first connecting the probe to pressure, allow pressure to build slowly (1 
psi/second) would be desirable.

External power cannot exceed 36 volts DC!  

When supplying external power to the Well Watch, care must be taken to insure that 
voltage spikes or induced transients are not conducted into the unit. Over voltage and 
surge protectors and proper grounding should be used if this is a possibility.

Use surge suppressors and grounding on signal lines!  

When connecting the Well Watch to remote equipment through the RS232 port or 
analog outputs, care is required to prevent ground loops, lightning induced transients 
etc from reaching the Well Watch. Over voltage and surge protectors and proper 
grounding should be used if this is a possibility.

FCC Warning Statement. 

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS 
SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT 
CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY 
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE 
UNDESIRED OPERATION. 

NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR 
MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE 
FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S 
AUTHORITY TO OPERATE THE EQUIPMENT. 

  Eno Scientific  Well Watch 700

Page 

7

   

Содержание Well Watch 700
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды