Engl INVADER II Скачать руководство пользователя страница 31

Страница: 31 / 40

Troubleshooting

Programmable features fail to respond when you change settings:

The amp fails to respond when you try to switch presets via MIDI foot board.

The amp is not providing an output signal / no sound is emanating from the
speaker.

-> Powerful static charges, strong radio signals or mains voltage spikes can affect

microcontroller-driven systems, setting them to an undefined status (commonly

called a hung chip). In this event, your only choice is to reset the system.

Simply switch the amp off and on again.

-> If a reset doesn't solve the problem that is, the chip is still hung there

is a defect in the control system (presumably on the logic board holding

the microcontroller). In this case, consult an authorized service center

or a professional specialist.

-> Is the MIDI foot board connected to the MIDI In port (44)?

-> Is the MIDI cord you are using intact and wired properly?

(Refer to page 35 for pin assignments.)

-> Is the amp set to the MIDI channel over which the MIDI foot board is sending

program change commands? You can set the DIP switch (46) to OMNI

reception to check if the preamp is actually receiving data.

-> Is another foot board (the ENGL Z-9 or a two-way footswitch) connected and

therefore blocking MIDI reception?

-> Is at least one speaker connected to the speaker outputs

(62, 63)

(64, 65) or

(66)?

-> Is the power amp activated (Standby switch to ON)?

Standby / power amp off => The Mute LED (36) on the front panel

indicates the Amp Mute status.

-> Are all cords (guitar, effect, and speaker) connected properly and are they

functional?

-> Unplug connected effectors and see if the preamp works fine without these

peripheral devices.

-> Is the

activated in one of the channels

and

the Threshold (49) knob set to a high value? Deactivate the

(17)

for a quick check.

-> Are the active Master knob and the Gain and Volume knobs set to a value

greater than 0? If any of these knobs is set to 0, no signal is routed

to the amp's outputs.

-> Did you select a MIDI preset programmed with

enabled?

The front panel Mute LED (36) lights up to indicate

is active.

-> Did you send via MIDI foot board a MIDI controller #7 (or #28) command

with a value more than or equal to 5? This activates A

, thereby

silencing the amp. The front panel Mute LED (36) lights up to indicate

is active.

4 Ohms

, 8 Ohms

16 Ohms

Noise Gate

CH2 CH3

CH4

Noise Gate

Amp Mute

mp Mute

Amp Mute

Содержание INVADER II









































Результаты поиска

Содержание INVADER II

Отзывы:

Похожие инструкции для INVADER II

Бренды по названию

Популярные бренды

Engl INVADER II, Руководство оператора

Результаты поиска

Содержание INVADER II

Отзывы:

Похожие инструкции для INVADER II

Бренды по названию

Популярные бренды