Mounting
screws
Installation
screws
7
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
Installation:
IMPORTANT NOTES:
1. Find a suitable location to mount the keypad. Install it at the height at which most users will be
able to easily operate the keypad.
2.
,QVWDOORQHPRXQWLQJVFUHZRQWKHZDOO$IWHUWKHVFUHZKDVEHHQLQVWDOOHGKDQJWKHEDFNER[
by the top mounting hole.
3. Install the second mounting screw through the bottom hole.
4.
5XQWKHZLUHWKURXJKWKHZDOORUFRQGXLWWRWKHEDFNER[ORFDWLRQWKHQUXQWKHZLUHWKURXJKWKH
EDFNER[
5. Connect the wires to the keypad according to the wiring diagram on page 8.
6.
)LQLVKDVVHPEO\E\DWWDFKLQJWKHNH\SDGWRWKHEDFNER[ZLWKWKHLQFOXGHGLQVWDOODWLRQVFUHZV
1.
$OZD\VGLVFRQQHFWSRZHUEHIRUHVHUYLFLQJWKHNH\SDG'RQRWDSSO\SRZHUXQWLODOOFRQQHFWLRQ
wiring is completed.
2.
7KHNH\SDGPXVWEHSURSHUO\JURXQGHG8VHDPLQLPXPRI$:*ZLUHFRQQHFWHGWRWKH
ground terminal. Failure to do so may damage the keypad.
3. All wiring and programming should be done by a professional installer to reduce the risk of
improper installation.
4.
7KHXVHU¶VJXLGHIRUWKLVNH\SDGLVORFDWHGRQSDJHRIWKLVPDQXDO%HVXUHWRVWRUHWKLV
manual in a safe place for future reference.
IF USING THE KEYPAD WITH A MECHANICALLY
OPERATED DOOR OR GATE, MOUNT THE KEYPAD AT
LEAST 15’ (5m) FROM THE DOOR OR GATE TO PREVENT
USERS FROM BEING CRUSHED OR PINNED. FAILURE TO
DO SO MAY RESULT IN SERIOUS INJURY OR DEATH.
18
ENFORCER Access Control Keypad
SECO-LARM U.S.A., Inc.
The keypad can be programmed so that the output is disabled for a certain period of time every
day. The output will be disabled at the start time, and will be re-enabled at the end time. This
ensures that users are not allowed into the protected premises, such as during lunch hour or at
night.
NOTE:
•
The real-time clock must be operating in order to set the output auto-disable time (see
³3URJUDPPLQJWKH5HDO7LPH&ORFN´RQSDJH
•
For safety purposes, the egress button still works while the output is auto-disabled.
•
The time is set using the military (24-hour) time format (00:00 to 23:59).
•
If the programmed start time is before the end time, the output is auto-disabled within a single
day. If the programmed start time is after the end time, the end time will be on the
following day.
•
The start time and end time cannot be the same.
•
The auto-disable time can be temporarily paused and restarted using the super user code (see
³3URJUDPPLQJWKH6XSHU8VHU&RGH´RQSDJHVa
•
'XULQJWKHDXWRGLVDEOHWLPHWKHVXSHUXVHUFRGHFDQEHXVHGWRRSHUDWHWKHRXWSXW
•
7KHUHG/('ZLOOUHPDLQOLWGXULQJWKHDXWRGLVDEOHWLPH
When programming the auto-disable time, use this general formula:
++00++00
±3URJUDP$XWR'LVDEOH7LPH
++00
– Start Time
++00
±(QG7LPH
Start Time:
•
Start time for the auto-disable time.
++
represents hours and
00
represents minutes in
the military (24-hour) time format, from 00:00 to 23:59.
End Time:
•
(QGWLPHIRUWKHDXWRGLVDEOHWLPH
++
represents hours and
00
represents
minutes in the military (24-hour) time format, from 00:00 to 23:59.
Examples
LQWKHVHH[DPSOHVDVVXPHWKDWWKHVXSHUXVHUFRGHLV
):
1.
,QSURJUDPPLQJPRGHVHWWKHDXWRGLVDEOHWLPHIURP30WR30
2.
,QSURJUDPPLQJPRGHVHWWKHDXWRGLVDEOHWLPHIURP30WR$0WKHIROORZLQJGD\
Programming the Auto-Disable Time:
