background image

KP2000E/EM Series Style Keypad

Installation and Programming Instructions
Models KP2000EXX and KP2000EMXX

23852973

Specifications

Parameter

Specifications

Voltage 
Requirements

10-30 VDC; 12-24VAC

Keypad Current 
Requirements (Max)

VDC

VAC

10V: 85mA

12V: 150mA

30V: 115mA

24V: 200mA

Relay Contact Rating 2A @ 30VDC (Main & Aux)
REX Input

Normally Open Dry Contact

Door Position Switch 
Input

Normally Closed Dry Contact

Mechanical 
Dimensions

4.50” H x 2.75” W x 0.60” D 

Environment

Indoor or Outdoor

Temperature 
Tolerance

-31°F to 151°F (-35ºC to 66°C)

Front End Cable 
Type

Stranded and Shielded

Front End Distance 
and Wire Gauge

1000 Ft. – 18AWG; 500 Ft – 20 AWG; 250 
Ft. – 22 AWG

Firmware Version

1.0x (“1” is the major version; “0” is the 
minor version; “x” is a minor version, 
reserved for bug fixes, which is indicated 
with a letter, such as “a”.)

Keypad Operating Modes

The KP2000E/EM Series keypad has two operating modes: 
Standalone Mode and Wiegand Front End Mode. Below is a brief 
explanation of each mode. Refer to the programming section for 
details about selecting each mode.

Standalone Mode:

By default, the keypad is programmed for Standalone Mode. In this 
mode, all the users and other programming options are maintained 
within the keypad and no additional controller is required. The lock 
and all other inputs and outputs are connected directly to the keypad.

Wiegand Front End Mode:

In Wiegand Front End mode, a separate UL Listed compatible 
Wiegand Access Control panel is required. When you enter a code on 
the keypad it is then sent to the control panel as Wiegand card data, 
depending on which format you’ve programmed it for. The control 
panel maintains the users and programming options and makes all 
the access control decisions. The locking device and all inputs and 
outputs are connected to the control panel.

Mounting the Keypad

The keypad is designed to be flush mounted using a standard UL 
Listed single-gang electrical box. Mounting height can vary depending 
on requirements. An appropriate range is typically between 48 and 52 
inches on center off the floor.
For outdoor installations, use a UL Listed weatherproof back box and 
seal the wire entry locations with silicone and provide a drain hole. 
For additional protection, install the provided foam gasket between 
the keypad and the back box. In addition, use the anti-oxidant grease 
pack for the wire harness connectors.

48 - 52”

Circuit Board Diagram

1

P2

Main

Relay

Aux

Relay

1

J2

1

J3

Note: J3 is NOT USED

Содержание KP2000EM Series









Отзывы: