background image

172 305 48  07-01

GENERAL INSTRUCTIONS

UV-Detector

This should not be exposed to tempe-
ratures exceeding 60°C. The current 
passing through the UV-detector, 
when it is being illuminated, should be 
at least 70 µ A for LFL1.. This current can 
be measured by means of a moving 
coil instrument. Checks should only 
be made if a fault is suspected.

The capacitor, which sould be placed 
between the terminals on the moving 
coil instrument, must be of 
100 µ F 10-25 V.

Gas pressure switches: 

Adjustment range:

 

2,5-50 mbar 

GW 50

 

5-150 mbar 

GW 150

Adjustment of min. gas pressure 
switch

The min. pressure switch should react 
if the gas pressure is too low and 
prevent the burner from starting. Too 
low a gas pressure during operation 
should stop the burrner. The burner 
may start again when the rated gas 
pressure has been reached.
Remove the protective cover. Con-
nect a pressure gauge for measuring 
the rated pressure. Decide on pressure 
at which  the gas switch should switch 
off. Set this pressure by means of the 
valve. Carefully turn the knob (see 

igure) until the gas pressure switch 

switches off. The value shown on the 
scale should then approximately cor-
respond with the value shown on the 
pressure gauge. Tolerance on scale 

appr. ± 15%. Open the ball valve.

Adjustment of max. gas pressure 
switch

The burner is equipped with a max. 
gas pressure switch only on request. 
It should stop the burner if the gas 
pressure exceeds the set value. The 
burner can then only be re-started 
manually (gas burner control or over-
pressure switch).
Remove the protective cover. Connect 
a pressure gauge for measuring the 
rated gas pressure. Decide on pres-
sure at which the gas pressure switch 
should switch off. Turn the adjustment 
knob to this value. Tolerance on the 

scale ±15%. 

Adjustment of air pressure switch

The air pressure switch should 
stop the burner if the air volume is 
reduced.

On  adjustment,  turn  the  scale  on 

the air pressure switch in clockwise 
direction. When the switch-off point 
has been reached and the burner 
stops read off the value on the scale.  
Then turn the scale in anti-clockwise 
direction to desired value. Make 
repeated start attempts to ensure 
that the air pressure switch is not too 
closely set. 

Air pressure switch:

Adjustment range ca: 

 

1-10 mbar 

LGW 10

 

2,5-50 mbar 

LGW 50

Flame monitoring

Gas pressure switch, air pressure 
switch

UV-detector

1

22

Control box LFL1

µ A

2

23

Содержание Bentone BG400





































Отзывы: