background image

7.3.  Maintenance and service

7.3.1.  WARNING: THERE ARE DANGEROUS VOLTAGES WITHIN THE 

BATTERY CHARGER CABINET. ONLY A QUALIFIED PERSON 
SHOULD ATTEMPT TO ADJUST OR SERVICE THIS BATTERY 
CHARGER

7.3.2.  The charger requires minimal maintenance. Connections and 

terminals should be kept clean and tight. The unit (especially the 
heatsink) should be periodically cleaned with a low pressure air to 
prevent any excessive dirt build up on components. Care should 
be taken not to bump or move any adjustments during cleaning. 
Make sure that both the AC lines and the battery are disconnected 
before cleaning. The frequency of this type of maintenance 
depends on the environment in which this unit is installed. 
For service, contact your sales representative or call:  
1-800-ENERSYS (USA) 1-800-363-7797

7.3.3.  Any data, descriptions or specifications set forth herein are subject 

to change without notice. Before using the product(s), the user 
is advised and cautioned to make its own determination and 
assessment of the suitability of the product(s) for the specific 
use in question and is further advised against relying on the 
information contained herein as it may relate to any general use or 
indistinct application. It is the ultimate responsibility of the user to 
ensure that the product is suited, and the information is applicable 
to the user’s specific application. The product(s) featured herein 
will be used under conditions beyond the manufacturer’s control 
and therefore all warranties, either express or implied, concerning 
the fitness or suitability of such product(s) for any particular use 
or in any specific application, are disclaimed. The user expressly 
assumes all risk and liability, whether based in contract, tort or 
otherwise, in connection with the use of the information contained 
herein or the product itself.

7. Service and Troubleshooting (cont.)

8

© 2021 EnerSys. All rights reserved. Trademarks and logos are the property of EnerSys and its affiliates except UL

®

which is not the property of EnerSys. Subject to revisions without prior notice. E.&O.E.  
AMER-EN-OM-NEX-PLCH-1221

www.enersys.com

www.experiencenexsys.com

-REV AB

Содержание NexSys+ NIP1









Отзывы: