EnerSys ALPHA PowerBay+ Half Size BDFB страница 24 Скачать руководство пользователя

Страница: 24 / 52

C048-741-30 R01, Rev. B (01/2020)

6.3

6.3 Settings Menu

Settings Menu

The Settings menu (

) allows the user to monitor and fine-tune

the BDFB system settings. Refer to interface map below for

menu layout.

Settings

┣

Volts Calibration

┣

Display

┃ ┣

Brightness

┃ ┗

Touch Calibration

┣

System

┗

Advanced

┣

BDFB Config

┃ ┗

Yes/No

┣

Memory

┃ ┗

Clear EEPROM

┃ ┗

Yes/No

┗

Test Modes

6.3.1

6.3.1 Volts Calibration

Volts Calibration

To calibrate the voltage per bus, adjust the voltage of each bus

by tapping the

(-)

(+)

buttons

(see Figure 45).

6.3.2

6.3.2 Display

Display

The Display

menu allows access to adjustment of screen

brightness as well as access to the touch calibration feature.

┗

Brightness:

Screen brightness can be adjusted by moving the

slider horizontally (see Figure 46).

┗

Touch Calibration:

This feature is used by tapping the circles that will

appear at three points on the screen to calibrate

the touch screen display (see Figure 47). Note: This

causes the controller to reset.

Figure 45. Volt Cal.

Figure 46. Brightness

Figure 47. Touch Cal.

Содержание ALPHA PowerBay+ Half Size BDFB





















































Результаты поиска

Содержание ALPHA PowerBay+ Half Size BDFB

Отзывы:

Похожие инструкции для ALPHA PowerBay+ Half Size BDFB

Бренды по названию

Популярные бренды

EnerSys ALPHA PowerBay+ Half Size BDFB, Техническое руководство

Результаты поиска

Содержание ALPHA PowerBay+ Half Size BDFB

Отзывы:

Похожие инструкции для ALPHA PowerBay+ Half Size BDFB

Бренды по названию

Популярные бренды