Enersol MFLR09, Руководство пользователя

Страница: 23 / 30

Page 23
Press and key simultaneously to enter in
programming Mode. Meter Start showing this Screen
.
Press key and select Network among following
using and keys.
Press key to edit network.
Select using and keys among
followings
Star: 3 Phase 4 Wires
(Default Value)
Delta: 3 Phase 3 Wires
Single: 1 Phase 2 Wires.
Press key to clear integrated
parameters. keep on pressing or
key till meter start showing
“YES”. and then press key. It will
clear energy, Run hours, power on
hours, power interruptions.
To avoid or move further press
key .
Press key to edit load type.
Select using and keys among
followings
Active: Watt & Wh
(Default Value)
Apparent: VA & VAh
Reactive: VAr & VArh
meter will show only that power/
energy which you select here.
Press key to edit PT ratio.
First digit start blinking and set that
digit using and keys. then
press to go to second digit.
Repeat the same till 4th digit.
After 4th digit, press and decimal
point start blinking. Locate it using
and key(s).
for Ex: if PT is 11000/415, then set
P ratio = 26.50
Press key and then press to
move to next page
Press key to edit nos of poles.
First digit start blinking and set that
digit using and keys. then
press to go to second digit.
( Default value is 04)
Press key and then press to
move to next page
Press key to edit MODBUS ID.
First digit start blinking and set that
digit using and keys. then
press to go to second digit & so
on.
( Default value is 001)
Press key and then press to
move to next page
Press key to edit Baud Rate.
set baud rate using & key
among followings
1200, 2400, 4800, 9600, 19.2K,
38.40K
(default value id 9600)
Press key and then press to
move to next page
Press key to edit Parity.
set parity using & key among
followings
EVEN, ODD & NONE
(default value id EVEN)
Press key and then press to
move to next page
Press key to save the changes.
press & key till meter start
blinking “YES” and then press to
save.
OR
Press & key till meter start
blinking “NO” and then press to
ignore the changes and restore
previous values.
Press to again edit the
configuration
OR
Press key and Set CT ratio. Enter digit which is
blinking using and keys & then press key to
move to second digit. Repeat this till last digit and then
press key.
ex:- if you are using a CT of 200/5 then Enter 0040
Press key to edit again or press key move forward
Press key and Set PT ratio. Enter digit which is
blinking using and keys & then press key to
move to second digit. Repeat this till Decimal point and
then press key.
ex:- if you are using a PT of 415/110 then enter 3.773
Press key to edit again or press key move forward
Press key and this screen appears on the Display.
First digit start Blinking. Set this digit equals to 1 using
and/or key(s).Now Press key four more times.
Failed to follow these steps will result in reset of the
value entered and first digit again start blinking. One
need to do the same until it becomes
1000 .
Press and key
simultaneously to enter in
programming Mode.
Meter Start showing this Screen.
Press to proceed further.
Password digit start Blinking. Set
digit equals to 1 using and/or
key(s).
Now Press key four more times.
Failed to follow these steps will
result in reset of the value entered
and first digit again start blinking.
One need to do the same until it
becomes
1000
(Default password)
: Star Configuration( 3 phase 4 wire ).
: Delta Configuration( 3 phase 3 wire ).
: Single Phase ( 1 phase 2 wire ).
Press key after Selecting and then press .
Press key after Selecting and
then press .
Press key after Selecting and
then press .
Press key if one needs to clear the Integrated
parameters. Use and key till “ YES ” string start
appearing on screen and then press . This will clear
Total and Per phase energy, No. of interruptions, Run
and Power ON Hours.
Otherwise Press key to avoid this action
Press key and set the No of Poles. Enter the
blinking digit using the and keys. Repeat this
till the last digit and press .
Press key and Set Device ID for MODBUS. Enter
the blinking digit using the and keys. Repeat this
till the last digit and press .
note: Valid Device ID ranges from 001 to 247.
Press key and Config the Baud rate using and
Key. After Configuring press then press key
Press key to edit again or press key move forward
Press key to edit again or press key move forward
Press key to edit again or press key move forward
Press key and select MODBUS parity using and
Press key after Selecting and then press .
: None
: Even Parity
: Odd Parity
If one needs further Editing then press key else
press key. A string on the screen starts Blinking. use
and key till screen start displaying “YES”. Then
press key to save all the changes. if one press
key while meter displaying “NO”, then meter will not
save changes and restore previous Settings one.
Time Saving Tip
One can see all the Config settings in the set para page rather than
always going to Programming mode to see configured Settings
Note: If Meter observe no activity for more than 1 minute while in
Programming Mode, then it will automatically return back in normal
Mode without saving any changes.
10. Programming Guide
LCD
LCD
LCD
LCD
LCD
LCD
LCD
LCD
LCD
LCD
LCD
Series
Series
Series
Series
Series
Series
Series
Series
Series
Series
Series
ENERSOL
ENERSOL
ENERSOL
ENERSOL
ENERSOL
ENERSOL
ENERSOL
ENERSOL
ENERSOL
ENERSOL
ENERSOL
MFLR09
MFLR09
MFLR09
MFLR09
MFLR09
MFLR09
MFLR09
MFLR09
MFLR09
MFLR09
MFLR09
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
PROG
COM
COM
COM
COM
COM
COM
COM
COM
COM
COM
COM
Prog. Mode
Password
Network:
Clr Intg Para
Pole:
Device ID:
Baud Rate:
Parity:
Save:
Load:
PT Ratio:
0000
Star
----
04
001
9600
EVEN
----
Active
0001
.