background image

15

9.5  Blade Replacement

The use of worn blades decreases the effectiveness of 

the cutter and can also side load the cylinder, possibly 

damaging the tool. Pump overheating may also occur.
Replace blades immediately when it is noticed that 

they are worn and/or damaged, or if there has been a 

noticeable decrease in cutting performance.
The cutter contains a fixed blade and a moving blade. 

Refer to Section 9.5.1 for fixed blade replacement 

instructions and to Section 9.5.2 for moving blade 

replacement procedures.

 

NOTICE:

  CAUTION

Use extreme caution when removing 

and installing blades. Blades may be sharp even 

when worn. To avoid hand injury, wear appropriate 

hand protection and avoid contact with blade cutting 

edges.

 

NOTICE

To help ensure even blade wear and optimum 

cutting performance, it is recommended that both the 

fixed blade and the moving blade be replaced at the 

same time.

9.5.1  Fixed Blade Replacement

Replace the fixed blade as described in the following 

steps. Refer to Figure 12.
1. Start the pump. Move the piston to the “home” 

position (fully retracted). See Figure 8.

2. Stop the pump. Be sure that hydraulic pressure is 

completely relieved.

3. Disconnect pump from AC power supply.

 

NOTICE:

  WARNING

Always disconnect pump from AC 

power supply before beginning cutter blade 

replacement procedures. Failure to observe this 

precaution could result in accidental startup as 

procedures are being performed. Serious personal 

injury could result.

4. Place the cutter horizontally on a stable work surface.
5. Open the cutting head. Refer to Section 7.2 for 

additional information.

6. Remove retaining ring (Figure 12, item 1B). Remove 

clevis pin (Figure 12, item 5) and cutting head 

 

(Figure 12, items 6-14).

7. 

For model EWCH90, remove nine capscrews 

 

(Figure 12, item 6), washers (Figure 12, item 13) 

and nuts (Figure 12, item 14). For model EWCH140, 

remove six socket head screws, washers and nuts.

8. Separate left side outer plate (Figure 12, item 9), inner 

plate (Figure 12, item 11) and right side outer plate 

(Figure 12, item 12).

9. For model EWCH90, remove eight fixed blade 

screws (Figure 12, item 7) and washers (Figure 12,  

item 8) and remove fixed blade (Figure 12, item 10). For  

model EWCH140 remove seven fixed blade screws 

and washers and remove blade.

10. For model EWCH90, install new fixed blade 

 

(Figure 12, item 10) onto left side outer plate 

 

(Figure 12, item 9) with eight fixed blade screws 

(Figure 12, item 7) and lock washers (Figure 12,  

item 8) and torque to 91 in-lb [10 Nm]. Also apply 

Loctite 243 or equivalent.

11. For model EWCH140, install new fixed blade 

 

(Figure 12, item 10) onto left side outer plate 

 

(Figure 12, item 9) with seven fixed blade screws 

(Figure 12, item 7) and lock washers (Figure 12,  

item 8) and torque to 18 ft-lb [25 Nm]. Also apply 

Loctite 243 or equivalent.

12.  Assemble the left side outer plate (Figure 12, item 9), 

inner plate (Figure 12, item 11) and right side outer 

plate (Figure 12, item 12) using nine capscrews 

(Figure 12, item 6), washers (Figure 12, item 13) 

and nuts (Figure 12, item 14) for model EWCH90 

and six socket screws, washers and nuts for 

 

model EWCH140. Torque to 155 ft-lb [211 Nm]. Also 

apply Loctite 243 or equivalent.

13. Attach cutting head (Figure 12, items 6-14) to 

tool body using clevis pin (Figure 12, item 5) and 

retaining ring (Figure 12, item 1B).

14. Close the cutting head. Refer to Section 7.2 for 

additional information.

15.  Test for proper operation before placing the cutter 

back into service.

Содержание EWCH140





















Отзывы: