background image

 

Safety Guidelines

 

 

Exposure to ultraviolet light is dangerous, both direct and reflected. UV can produce eye 
injuries and skin erythema. These effects are considered transient. UV may also be 
carcinogenic but since it has very limited penetrating ability it is unlikely to cause damage to 
anything besides outer layers of skin or other exposed surfaces. 
 
The Energenics UV-MAX is designed for zero user exposure to UV; however, we will review 
safety factors regarding UV for better knowledge and understanding. 
 
 

Protective Clothing and Eyewear 

 
 
It is not recommended that any personnel be subject to direct UV exposure. In the event such 
exposure is probable, personnel should wear PPE providing full coverage of exposed skin and 
appropriate eye protection. 
 
UV safety glasses designed to filter UV-C and those of the wrap-around type are 
recommended. Be aware, not all glasses offer complete coverage or UV-C filtering. 
 
 

OSHA Guidelines for Ultraviolet Exposure 

 
 
OSHA provides technical guidance regarding protecting employees from ultraviolet light with 
respect to laser hazards. You can find this guidance in the (

OSHA Technical Manual

 (TED 1-

0.15A, Section III 

– Chapter 6)). The relevant chapter includes information on control 

measures and safety programs for laser hazards associated with exposure to UV. This is the 
best documented guideline available. 

 

 

NIOSH Limits 

 
 
The National Institute of Occupational Safety and Health (NIOSH) provide a recommended 

exposure level (REL) for UVGI at 6 mJ/cm2 (or 0.006 J/cm2).

 

Содержание UV-MAX














Отзывы: