background image

ii 

©2010 Enerdrive Pty Ltd

Disclaimer of Liability

Since the use of this manual and the conditions or methods of installation, operation, 

use and maintenance of the ME-BMK is beyond the control of MagnaSine this 

company does not assume responsibility and expressly disclaims liability for loss, 

damage or expense, whether direct, indirect, consequential or incidental, arising out 

of or anyway connected with such installation, operation, use, or maintenance.
Due to continuous improvements and product updates, the images shown in this 

manual may not exactly match the unit purchased.
Restrictions on Use
The ME-BMK shall not be used in connection with life support systems, life saving 

or other medical equipment or devices.  Using the ME-BMK with this particular 

equipment is at your own risk.

IMPORTANT PRODUCT SAFETY INSTRUCTIONS
This manual contains important safety instructions that must be followed during the 

installation and operation of this product.  Read all instructions and safety informa-

tion contained in this manual before installing or using this product.

WARNINGS:

•  All electrical work must be performed in accordance with local, state and federal 

electrical codes.
•  This product is designed for indoor / compartment installation.  It must not be 

exposed to rain, snow, moisture or liquids of any type.
•  Use insulated tools to reduce the chance of electrical shock or accidental short 

circuits.
•  Remove all jewelry such as rings, watches, bracelets, etc., when installing or 

performing maintenance on the ME-BMK and inverter system.
•  Always disconnect the batteries or energy source prior to installing or perform-

ing maintenance on the ME-BMK and inverter system.  Live power may be present 

at more than one point since an inverter utilizes both batteries and AC.  Turning 

off the inverter may not reduce this risk.  As long as AC power is connected, it will 

pass thru the inverter regardless of the power switch on the inverter or the ON/

OFF INVERTER pushbutton on the remote.
Safety Symbols
To reduce the risk of electrical shock, fire, or other safety hazard, the following 

safety symbols have been placed throughout this manual to indicate dangerous 

and important safety instructions.

WARNING: This symbol indicates that failure to take a specified action 

could result in physical harm to the user.

CAUTION: This symbol indicates that failure to take a specified action 

could result in damage to the equipment.

Info: This symbol indicates information that emphasizes or supplements 

important points of the main text.

Содержание MagnaSine ME-BMK

























Отзывы: