Eneo Fastrax III EDC-3182 Скачать руководство пользователя | Manualshive

Страница: 37 / 44

background image

37

4. Troubleshooting

If problems occur, verify the installation of the camera with the instructions in this manual and with other operating equipment. Isolate the problem to the
specific piece of equipment in the system and refer to the equipment manual for further information.

Problem

Possible Solution

No video

Verify that power is connected to all pieces of equipment in the system.
Verify that the power switches are in the ON position.
Check the video connections.

Poor video quality

Check that the BNC connectors are inserted properly.
Check the voltage level of the dome camera.
Check that 8 pin cable is connected to the Keyboard.
Check 8 pin cable for Keyboard is proprietary. (Cable for video is shielded.)

Dome cameras lose their positions.

Reset the cameras using the Dome configuration menus.
Check that the dome cameras are inserted properly in the base.
Check the voltage level of the dome camera.

Camera number does not match the multiplexer number.

Check the camera ID and insert the BNC cable into the proper input of the multiplexer.

Picture is torn when switching

Check Line Lock setting and adjust phase of L/L.

«
...
35
36
37
38
39
...
»

Содержание Fastrax III EDC-3182













































Отзывы:

Нет отзывов

Похожие инструкции для Fastrax III EDC-3182

Бренд: Zivif Страницы: 14

Бренд: CAME Страницы: 80

Бренд: TDSi Страницы: 2

Бренд: U-Prox Страницы: 29

JV-B765HV9V22DNR

Бренд: JV vision Страницы: 12

Бренд: NAPCO Страницы: 4

NVIP-3DN7000V/IRH-2P

Бренд: Novus Страницы: 24

Бренд: FLIR Страницы: 2

Бренд: Smanos Страницы: 15

TRANSCENDENT VTD-TND5RME

Бренд: Vitek Страницы: 8

Бренд: Triton Страницы: 12

Бренд: Q-See Страницы: 11

Бренд: Lexing Страницы: 4

Бренд: Dahua Страницы: 18

Бренд: NA-DE Страницы: 2

Бренд: Nexvoo Страницы: 19

Multi-Purpose Device 333010-CE

Бренд: CMC Rescue Страницы: 30

Бренд: Qihan Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды