Endress+Hauser Proline t-mass 65 MODBUS RS485 Скачать руководство пользователя страница 36

Страница: 36 / 62

PROCESS PARAMETER

Proline t-mass 65 MODBUS RS485

Hauser

REFERENCE DENSITY

Prerequisite

This function is

not

available if the IN-SITU CALIBRATION function has been

enabled.
Contact your Hauser service organization for more information.

Description

Use this function to display the calculated reference density (for corrected
volume flow measurement).
The unit is taken from the function UNIT DENSITY (



10).

Display

5-digit floating-point number

MODBUS register:
Data type:
Access:

5130
Float
read

NET CALORIFIC VALUE

Prerequisite

This function is

only

available if AUTO NET or MANUAL was selected in the

MODE 1 or 2 function (



44)

Description

Use this function to display the current net calorific value of the gas.
The unit is taken from the function UNIT CALORIFIC VALUE MASS (



or UNIT CALORIFIC VALUE CORRECTED VOLUME (



9).

Display

5-digit floating-point number

MODBUS register:
Data type:
Access:

5272
Float
read

GROSS CALORIFIC VALUE

Prerequisite

This function is

only

available if AUTO GROSS was selected in the MODE 1 or

2 function (



44).

Description

Use this function to display the current gross calorific value of the gas.
The unit is taken from the function UNIT CALORIFIC VALUE MASS (



or UNIT CALORIFIC VALUE CORRECTED VOLUME (



9).

Display

5-digit floating-point number

MODBUS register:
Data type:
Access:

5274
Float
read

MOLE % GAS 1

Description

Use this function to display the Mole % of GAS TYPE 1.

Display

0.0 % to 100.0 %

MODBUS register:
Data type:
Access:

5276
Float
read

ASSIGN LOW FLOW CUT OFF

Description

For selecting the process variable on which low flow cut off should act.

Options

0 = OFF
1 = MASS FLOW
2 = CORRECTED VOLUME FLOW

Factory setting

MASS FLOW

MODBUS register:
Data type:
Access:

5101
Integer
read/write

Function description, PROCESS PARAMETER group

Содержание Proline t-mass 65 MODBUS RS485































































Результаты поиска

Содержание Proline t-mass 65 MODBUS RS485

Отзывы:

Похожие инструкции для Proline t-mass 65 MODBUS RS485

Бренды по названию

Популярные бренды

Endress+Hauser Proline t-mass 65 MODBUS RS485, Руководство пользователя

Результаты поиска

Содержание Proline t-mass 65 MODBUS RS485

Отзывы:

Похожие инструкции для Proline t-mass 65 MODBUS RS485

Бренды по названию

Популярные бренды