Endress+Hauser Proline Promag 55 Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 130

background image

Device functions Proline Promag 55 FOUNDATION Fieldbus

3 Transducer Block

Hauser

87

EPD - Response
Time

AUTO - OOS

Use this parameter to enter the time span in which the criteria for an
empty pipe have to be satisfied without interruption before an error
message is generated.

User input:

fixed point number: 1.0 to 100 s

Factory setting:

1.0 s

EPD - Threshold

read only

This parameter is only used in the event of a service call.

EPD - Electrode

AUTO - OOS

Use this parameter to check whether the sensor is equipped with an EPD
electrode.

User interface:

YES - NO

Factory setting:

YES

→

Electrode fitted as standard

EPD - Low Value

read only

This parameter is only used in the event of a service call.

EPD - High Value

read only

This parameter is only used in the event of a service call.

EPD - Period

read only

This parameter is only used in the event of a service call.

Density Param. -
Fixed Value

AUTO - OOS

Use this parameter to enter a density factor (preferably at process
temperature or reference temperature) which is used to convert the
volume flow to a mass flow.

!

Note!

The unit is taken from the "Density Param. - Unit" parameter
(

User input:

5-digit floating-point number

Factory setting:

1 [unit]

Density Param. -
Unit

read only

Use this function to display the unit selected in the "System Unit - Fixed
Density" parameter for the fixed density value (

Sensor Data -
K-Factor Positive

AUTO - OOS

Use this function to display the actual calibration factor (positive flow
direction) for the sensor. The calibration factor is determined and set at
the factory.

User interface:

5-digit fixed point number: 0.5000 to 2.0000

Factory setting:

Depends on nominal diameter and calibration

Sensor Data -
K-Factor Negative

AUTO - OOS

Use this function to display the actual calibration factor (negative flow
direction) for the sensor. The calibration factor is determined and set at
the factory.

User interface:

5-digit fixed point number: 0.5000 to 2.0000

Factory setting:

Depends on nominal diameter and calibration

"Flow" Transducer Block/base index 1400

Parameter

Write access with

operating mode

(MODE_BLK)

Description

«
...
85
86
87
88
89
...
»

Содержание Proline Promag 55



































































































































Отзывы:

Нет отзывов

Похожие инструкции для Proline Promag 55

Бренд: CAME Страницы: 2

Бренд: N-Com Страницы: 28

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 3

ECONAVI CZ-CENSC1

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 9

AR42P9W - Plasma Panel anti-glare Filter

Бренд: Panasonic Страницы: 5

Бренд: Tamron Страницы: 3

Бренд: Banner Страницы: 2

Бренд: zenitech Страницы: 16

COMSPHERE 6800 Series

Бренд: Paradyne Страницы: 155

COMSPHERE 6800 Series

Бренд: Paradyne Страницы: 44

AERASGARD RCO2-W

Бренд: S+S Regeltechnik Страницы: 32

5500DN - Phaser B/W Laser Printer

Бренд: Xerox Страницы: 2

3600B - Phaser B/W Laser Printer

Бренд: Xerox Страницы: 2

Бренд: ICON Страницы: 2

Power commander GSXR750

Бренд: Dynojet Страницы: 4

V2 SUPERCHARGER

Бренд: Tesla Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды