Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 206

Страница: 206 / 272

Description of device parameters

Proline Promag 300 Modbus RS485

206

Hauser

Additional information

Dependency

The input range is dependent on the option selected in the

Current span

parameter

(→  106).

FreqOutputSim 1 to n



Navigation

 Expert → Diagnostics → Simulation → FreqOutputSim 1 to n (0472–1 to n)

Prerequisite

In the

Operating mode

parameter (→  120), the

Frequency

option is selected.

Description

Use this function to switch simulation of the frequency output on and off. The display

alternates between the measured value and a diagnostic message of the "Function check"

category (C) while simulation is in progress.

Selection

• Off

• On

Factory setting

Off

Additional information

Description

The desired simulation value is defined in the

Freq value 1 to n

parameter.

Selection

• Off

Frequency simulation is switched off. The device is in normal measuring mode or

another process variable is being simulated.

• On

Frequency simulation is active.

Freq value 1 to n



Navigation

 Expert → Diagnostics → Simulation → Freq value 1 to n (0473–1 to n)

Prerequisite

In the

FreqOutputSim 1 to n

parameter, the

option is selected.

Description

Use this function to enter a frequency value for the simulation. In this way, users can verify

the correct adjustment of the frequency output and the correct function of downstream

switching units.

User entry

0.0 to 12

500.0 Hz

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды