Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 204

Страница: 204 / 272

Description of device parameters

Proline Promag 300 Modbus RS485

204

Hauser

Additional information

Description

The desired simulation value is defined in the

Signal level

parameter (→  204).

Selection

• Off

Simulation for the status input is switched off. The device is in normal measuring mode

or another process variable is being simulated.

• On

Simulation for the status input is active.

Signal level



Navigation

 Expert → Diagnostics → Simulation → Signal level (1356)

Prerequisite

In the

Status inp. sim.

parameter (→  203), the

option is selected.

Description

Use this function to select the signal level for the simulation of the status input. In this

way, users can verify the correct configuration of the status input and the correct function

of upstream feed-in units.

Selection

• High

• Low

Curr.inp 1 to n sim.



Navigation

 Expert → Diagnostics → Simulation → Curr.inp 1 to n sim. (1608–1 to n)

Description

Option for switching simulation of the current input on and off. The display alternates

between the measured value and a diagnostic message of the "Function check" category (C)

while simulation is in progress.

The desired simulation value is defined in the

Value curr.inp 1 to n

parameter.

Selection

• Off

• On

Factory setting

Off

Additional information

Selection

• Off

Current simulation is switched off. The device is in normal measuring mode or another

process variable is being simulated.

• On

Current simulation is active.

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды