Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 122

Страница: 122 / 272

Description of device parameters

Proline Promag 300 Modbus RS485

122

Hauser

U[V]

A0026885

 9

Alarm, low level

Assign pulse 1 to n



Navigation

 Expert → Output → PFS output 1 to n → Assign pulse 1 to n (0460–1 to n)

Prerequisite

The

Pulse

option is selected in the

Operating mode

parameter (→  120).

Description

Use this function to select the process variable for the pulse output.

Selection

• Off

• Volume flow

• Mass flow

• Correct.vol.flow

Factory setting

Off

Value per pulse



Navigation

 Expert → Output → PFS output 1 to n → Value per pulse (0455–1 to n)

Prerequisite

In the

Operating mode

parameter (→  120), the

Pulse

option is selected, and one of

the following options is selected in the

Assign pulse

parameter (→  122):

• Mass flow

• Volume flow

• Correct.vol.flow

Description

Use this function to enter the value for the measured value that a pulse is equivalent to.

User entry

Signed floating-point number

Factory setting

Depends on country and nominal diameter→  213

Additional information

Entry

Weighting of the pulse output with a quantity.
The lower the pulse value, the

• better the resolution.

• the higher the frequency of the pulse response.

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды