Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 107

Страница: 107 / 272

Proline Promag 300 Modbus RS485

Description of device parameters

Hauser

107

Additional information

Description

• In the event of a device alarm, the current output adopts the value specified in the

Failure mode

parameter (→  116).

• If the measured value is outside the measuring range, the diagnostic message

S441 Curr.output 1 to n

is displayed.

• The measuring range is specified via the

0/4 mA value

parameter (→  108) and

20 mA value

parameter (→  109).

"Fixed current" option

The current value is set via the

Fixed current

parameter (→  107).

Example

Shows the relationship between the current span for the output of the process variable and

the lower and upper alarm levels:

I [mA]

A0034351

Current span for process value

Lower level for signal on alarm

Upper level for signal on alarm

Selection

Options

4...20 mA NAMUR

3.8 to 20.5 mA

< 3.6 mA

> 21.95 mA

4...20 mA US

3.9 to 20.8 mA US

< 3.6 mA

> 21.95 mA

4...20 mA

4 to 20.5 mA

< 3.6 mA

> 21.95 mA

0...20 mA

0 to 20.5 mA

< 0 mA

> 21.95 mA

If the flow exceeds or falls below the upper or lower signal on alarm level, the

diagnostic message

S441 Curr.output 1 to n

is displayed.

Fixed current



Navigation

 Expert → Output → Curr.output 1 to n → Fixed current (0365–1 to n)

Prerequisite

The

Fixed current

option is selected in the

Current span

parameter (→  106).

Description

Use this function to enter a constant current value for the current output.

User entry

0 to 22.5 mA

Factory setting

22.5 mA

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды