Endress+Hauser Prolevel FMC 662 Скачать руководство пользователя

Страница: 17 / 52

2.3

Transmitter wiring

Warning!

•

Make electrical connections with the power supply switched off!

•

The PE terminal strip must be grounded externally (contact protection)!

•

When wiring up probes and sensors in explosion hazardous areas, observe the
instructions on the certificate and other local regulations.

Terminal strip

The terminal strip for cable diameters up to 2.5 mm

is located in a separate connection

compartment. Fig. 2.5 shows the wiring diagram for the Prolevel FMC 662 (Terminal 3 is
reserved for the internal protective ground):

•

Remove the plastic cover from the front of the connection compartment

•

Press out the pre-stamped cable entries as required
bottom: 5 x Pg 16, 4 x Pg 13.5; rear: 4 x Pg 16.

Power

The power requirements are printed on the nameplate at the right-hand side of the
nameplate, see also Section 2.6, "Technical Data".

•

If the specifications on the nameplate do not correspond to those of your
power supply, do not connect up - you may damage the instrument!

•

Connect the protective ground to the metallic terminal strip provided at the
left — this ensures safe isolation and contact protection.

•

Current output, relay outputs, power connection and sensor input are all
electrically isolated from one another.

Analogue outputs

Only one non-floating device can be connected to each of the current outputs.

•

There is no limit to the number of floating devices, other than that imposed by
considerations of the maximum load of 600

Ω

Relays

For the switching capacity of the relays see the technical data in Section 2.6.

•

Relays 1a and 1b are normally assigned to channel 1

•

Relays 2a and 2b are normally assigned to channel 2.

The assignment can be changed by software, see Section 4.4.

RS-485

[EEX ia] IIC

B DGND A

L+ L-
L1 N

L+

L-

16.

60 VD

85.

253 V

20.

55 V

20 m

Sensor

D-

DGND

-485

1 2 3

4 5

6 7

81 82

91 92

53 60

- + - +

BA143_12

current

channel

rel

ys channel

rel

ys channel

arm

rel

term

inal

ground external

opt

ional

terf

ace

probe channel

Com

og V

260Z

bus swi

tches

current channel

Fig. 2.5:
Terminal assignments for
Prolevel FMC 662

Warning!

Prolevel FMC 662

Chapter 2: Installation

Hauser

Содержание Prolevel FMC 662





















































Результаты поиска

Содержание Prolevel FMC 662

Отзывы:

Похожие инструкции для Prolevel FMC 662

Бренды по названию

Популярные бренды

Endress+Hauser Prolevel FMC 662, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Prolevel FMC 662

Отзывы:

Похожие инструкции для Prolevel FMC 662

Бренды по названию

Популярные бренды