Endress+Hauser Analytik Jena Multi X 2500 Скачать руководство пользователя страница 116

Страница: 116 / 124

Transport and storage

multi X 2500

116

Remove the combustion tube.

Detach the gas transfer line from the connections and remove it.

Remove the auto-protection assembly.

Remove the combustion furnace (

→

"Removing the combustion furnace", p. 116).

Detach all hoses or put the hose ends into small bags and attach them to the basic

device with adhesive tape.

Secure the top cover of the basic device and the maintenance flaps on the right-

hand side of the device with adhesive tape.

Detach the hose connection to the measuring cell from the sulfuric acid container

with outlet. Remove the safety attachment. Remove the empty sulfuric acid

container and rinse it.

Remove the storage container for the sensor electrode and rinse it.

Detach the electrical connection of the electrodes. Put all electrodes into their

original packaging. When doing this, observe the servicing and maintenance
instructions for the electrodes (

→

"Clean and store the electrode", p. 105).

Remove the measuring cell and rinse it.

WARNING! The electrolyte solution of the measuring cell "high sensitive" contains
concentrated acetic acid. Be careful when emptying the measuring cell!

Attach the extraction hose to the chlorine module using adhesive tape.

12.3

Removing and installing the combustion furnace

12.3.1

Removing the combustion furnace

WARNING

Danger of electric shock! Before removing the combustion furnace switch off the

multi X 2500 using the mains switch and disconnect the mains plug from the power

outlet!

CAUTION

There is a risk of burns on the combustion furnace! Only remove the combustion

furnace when the device is cold or allow the device to cool down sufficiently!

Exit the multiWin software. Allow the basic device to cool down.

Switch off the multi X 2500 and the chlorine module using the mains switch and

pull the mains plugs from the power outlet. Cut the gas supply.

Remove the top cover. Open the front doors and remove them from the device.

Remove the combustion tube (

→

"Removing and cleaning the open combustion

tube", p. 89 or "Removing and cleaning the multi-purpose combustion tube",
p. 100).

In the chlorine module

Содержание Analytik Jena Multi X 2500





























































































































Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды

Endress+Hauser Analytik Jena Multi X 2500, Руководство по эксплуатации

Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды