Endress+Hauser Analytik Jena Multi X 2500 Скачать руководство пользователя страница 100

Страница: 100 / 124

Maintenance and care

multi X 2500

100

10.4.4

Removing and cleaning the multi-purpose combustion tube

WARNING

Danger of explosion! The hose connections for argon and oxygen on the combustion

tube must not be mixed up when reinstalling the assembly.

CAUTION

Risk of burns! Only remove the combustion tube when the device is cold!

NOTICE

Alkaline salts (hand perspiration) cause crystallizations in the quartz glass when

heating the combustion furnace which reduce the service life of the combustion tube.
Do not touch the combustions tube with your bare hands during reinstallation. Wear

protective gloves. If necessary, clean the combustion tube externally before installing it

in the combustion furnace (e.g. by wiping it with moist cellulose).

NOTICE

Closing the seal when the combustion tube has not been inserted into the furnace may

destroy the pneumatic seal of the auto-protection assembly. Only move the toggle

switch down if a combustion tube has been inserted. Alternatively, we recommend to

cut the gas supply during maintenance.

Disconnect the gas transfer line from the sulfuric acid container with outlet in the

chlorine module.

Exit the multiWin control software and allow the analyzer to cool down.

Switch off the multi X 2500 and the chlorine module. Remove the mains plug from

the power outlet. Switch off the gas supply.

In vertical operating mode, remove the cover at the top.

Open the front doors of the analyzer.

Open the pneumatic seal to the auto-protection assembly. To

do this, move the toggle switch up. This releases the

combustion tube.

Allow the device to cool down.

Содержание Analytik Jena Multi X 2500





























































































































Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды

Endress+Hauser Analytik Jena Multi X 2500, Руководство по эксплуатации

Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды