ENDEVCO 2680M1 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 26

ENDEVCO 2680M1 Скачать руководство пользователя страница 6

ENDEVCO

www.endevco.com Tel: +1 (866) ENDEVCO [+1 (866) 363-3826]

IM 2680/5 083119

6

03

INITIAL INSPECTION

The charge amplifier is packed in a protective bag and packaged in

shipping cartons containing shock-absorbent materials to prevent in-transit

damage. However, upon receipt of the units, the customer should make

an inspection to be certain that no damage has occurred during shipment.

Obvious damage should be reported immediately to the carrier.
Inspect the contents of the shipping carton and verify that the applicable

accessories listed in Table 4 are included in the shipment with each

airborne amplifier.
Should it be necessary to return the amplifier to the factory, follow the

instructions in section 7.1 of this manual. It is recommended that an

applications engineer be contacted prior to returning the unit since many

problems can be resolved via telephone of email.

Figure 2: Model 2680

airborne amplifier

configured as a charge

amplifier.

Figure 3: Model 2685

airborne amplifier

configured as an IEPE

(ISOTRON) current

source and voltage

amplifier.

«
...
4
5
6
7
8
...
»

Содержание 2680M1



























Отзывы:

Нет отзывов