background image

EDM01-07: DAG 3.7G Card User Guide 

©2005 

Version 7: May 2006 

 

Each of the items shown below can be changed 

 

reset 

Reset the ethernet framers, set auto mode 

 

default 

Initialise the card and set the default settings 

 

auto 

Set autonegotiate mode, card will detect rate 

 

10 

Force 10BaseT mode, 10Mbps 

 

100 

Force 100BaseTX mode, 100Mbp 

 

1000 

Force 1000BaseT mode, 1000Mbps 

 

slen=X 

Capture X bytes of the packet content 

 

[no]varlen 

The card can operate in two modes, variable length capture 

(

varlen

), and fixed length capture (

novarlen

). 

In variable length capture mode, a maximum capture size is 

set with 

slen=N

 

bytes. This figure should be in the range 32 

to 9600 and is rounded down to the nearest multiple of 8.  
Packets longer than slen are truncated.  Packets shorter than 

slen will produce shorter records, saving bandwidth and 

storage space. 
In fixed length mode, packets longer than the selected slen 

are truncated to slen, but packets shorter than slen will 

produce records that are padded out to the slen length.  

 

Avoid large values of slen in fixed length mode, as short 

packets arriving will produce large padded records, wasting 

bandwidth and storage space.  

 

rxsplit 

Send data from Port A to Stream 0. 

Equivalent to Port B = Stream 2 

Send data from Port B to Stream 2. 

Equivalent to Port B = Stream 2 

 

rxmerge 

Send data from Port A to Stream 0. 

Send data from Port B to Stream 0. 

Equivalent to Port B = Stream 0 

 

Note: You can not change 

align64

. This is permanently set. 

 
 

Example 

For instance, if the card is configured with fixed length capture 

(

novarlen

)

, but 

configuration to variable length capture is wanted, removing or adding the "

no

prefix will change the setting

.

 Simply type: 

dagthree varlen 

linkA   noreset 10 
linkB   noreset 10 
packetA varlen slen=1536 align64 
packetB varlen slen=1536 align64 
packetA drop=0 
packetB drop=0 
rx      steer=stream0 
tx      noifaceswap nooverlap 
terf    terf_strip32 
pci     33MHz 64-bit buf=128MiB rxstreams=2 txstreams=1 mem=56:16:56:0 
Firmware: dag37gepci_erf_v2_5 3s1500fg456 2006/03/28 17:07:15  (user) Card 
Serial: 4925 MAC Address A: 00:00:00:00:00:00 MAC Address B: 
00:00:00:00:00:00 MAC Address C: 00:00:00:00:00:00 MAC Address D: 
00:00:00:00:00:00 
 

Содержание DAG 3.7G Series



































Отзывы: