ENCORP iSAVER DPFC 450 Скачать руководство пользователя страница 6

Страница: 6 / 28

– Page 6 –

Specifications

Standard Specification for iSaver 450 DPFC

Model

iSaver 450

Voltage Input

600 VAC 60Hz

Supply

Three Phase

Configuration

3 Phase – 4 Wire

Rating

450 kVAr

Current Rating

450A

Banks

1x50 +(4x100) kVAr

Sequence

1:2:2:2:2

Logic

The unit is designed to operate in steps of 50 kVAr

Minimum Step

70% of the lowest Bank Capacity (35 kVAr)

Control Operation

Controlled real time switching output based on load requirements.

Controller

Microcontroller based advanced electronic controller

Target Efficiency

> 98% (+/- 3%) for Canadian Voltage and frequency

iSaver Display

3 row crystal clear backlit LCD display of RMS values

Web Monitoring

On Line iSaver parameters display (PF, kVA, kVAh, kW, kWh, kVAr,
kVArh, Hz, V-THD, I-THD, Status, Alarms, Time Integrated data.

Diagnostic feature

iSaver internal key component functional analysis and status display

iSaver Monitor

Displays main and ISaver (panel) parameters locally and remotely

DG operation

Dedicated PF setting for DG operation

Displayed Data

PF, kVA, kVAh, kW, kWh, kVAr, kVArh, Hz, V-THD, I-THD

Main Protection

Short circuit and Over- load protection (MCCB 600A/50KA-3Pole)

Bank Protection

Short circuit and Over- load protection (MCCB & MCB) and Thermal
safety trip(s). Unit automatically resumes operation once fault is
corrected.

Protection

Thermostats operated over temperature protection of enclosure cham-
bers (Both Front and Capacitor Chamber), Harmonic Reactors and
Capacitors.

Construction

Robust Standalone metal enclosure (indoor application only)

Dimensions

2000 (H) x 1100 (W) x 750 (D) mm

Weight

620Kg [± 3 %]

Mounting

Floor Mounting with Foundation Bolts

Enclosure

Powder coated corrosion resistant sheet steel enclosure (RAL 7035)

Transient protection

Provided

Cable Entry

Bottom and side entry provision

Содержание iSAVER DPFC 450





























Результаты поиска

Содержание iSAVER DPFC 450

Отзывы:

Похожие инструкции для iSAVER DPFC 450

Бренды по названию

Популярные бренды

ENCORP iSAVER DPFC 450, Руководство по эксплуатации

Результаты поиска

Содержание iSAVER DPFC 450

Отзывы:

Похожие инструкции для iSAVER DPFC 450

Бренды по названию

Популярные бренды