background image

Users’ Manual 

EAN-26MH Horizontal inclinometer system  

  

  

 

Page

 | 

4

 

CAUTION: 

Caution messages calls attention to a procedure or practice, that if not properly followed 
may result in loss of data or damage to equipment. 

NOTE:

 

Note contains important information and is set off from regular text to draw the users’ 
attention. 

1.4  General information 

This users’ manual is intended to provide you with sufficient information on operation of model EAN-
26MH horizontal digital inclinometer and its mobile readout unit.  The manual also contains instructions 
on how to set-up for inserting inclinometer probe into the ABS inclinometer casing for purpose of taking 
settlement readings.  

NOTE:

 

Installation personnel must have a background of good installation practices and knowledge 
of the fundamentals of geotechnics. Novices may find it very difficult to carry on the 
installation work. The intricacies involved in installation are such that even if a single 
essential but apparently minor requirement is ignored or overlooked, the most reliable of 
instruments will be rendered useless. 

A lot of effort has been made in preparing this instruction manual. However the best of instruction 
manuals cannot provide for each and every condition in the field, which may affect performance of the 
sensor. Also, blindly following the instruction manual will not guarantee success. Sometimes, depending 
upon field conditions, installation personnel will have to consciously depart from the written text and use 
their knowledge and common sense to find the solution to a particular problem.      
This equipment should be installed, maintained and operated by qualified personnel. Any errors or 
omissions in installation, data or data interpretation are not the responsibility of Encardio-rite Electronics 
Pvt. Ltd. 
For details on how to install inclinometer casing, please refer to operating manual # WI 6002.103. 

1.5  List of Abbreviations  

3G 

 

3rd Generation of wireless mobile telecommunications technology 

4G 

 

4rth Generation of wireless mobile telecommunications technology 

CSV    

Comma Separated Values  

DI  

 

Digital Inclinometer  

EAN-26  

Digital Inclinometer System 

FTP    

File Transfer Protocol  

GPRS    

General Packet Radio Service  

GSM    

Global System for Mobile Communications  

LED 

 

Light Emitting Diode 

PC 

 

Personal Computer 

SIM    

Subscriber Identity Module  

URL    

Uniform Resource Locator  

USB    

Universal Serial Bus  

WDMS   

Web based Data Monitoring Service 

Wi-Fi   

Wireless Fidelity 

Содержание EAN-26MH























Отзывы: