background image

Laser Safety Notice

This laser safety information contains certification and product information
covering laser products known as optical Gigabaud Link Modules (GLMs),
Gigabit Interface Converters (GBICs), 1x9 and small form factor transceivers
sold as accessories to or incorporated in Emulex LightPulse host adapters. The
GLM, GBIC, 1x9 and small form factor transceiver are the primary cable
connection mechanisms for any optical port on the host adapter and hub. This
data is not intended to be a replacement for any safety regulations and
standards; relevant safety documents should always be consulted if necessary.
Contact Emulex Corporation with any questions or concerns about laser
safety.

Certification and Classification
Labeling Requirements
Product Information
Usage Restrictions
System Level Certification

Certification and Classification

LP6000 and LP7000E PCI host adapters may contain a laser product known as
an optical Gigabaud Link Module (GLM). The optical GLM is attached to the
host adapter using an 80−pin connector and extends through the mounting
bracket. In turn, the host adapter can be inserted into any host system's PCI
slot.

The LH5000 hub may contain a laser product known as a Gigabit Interface
Connector (GBIC). The GBIC provides the physical connector to the optical
cable. The GBIC can be inserted into any pluggable hub port.

The LP8000, LP850 and LP9000 PCI host adapter may contain a laser product
known as a Gigabit Interface Converter (GBIC) or an embedded 1x9
transceiver. The GBIC and or 1x9 transceiver provide the physical connection
to the optical cable, and its SC−style connector extends through the mounting
bracket. In turn, the host adapter can be inserted into any host system’s PCI
slot.

The LP9002, LP9002L, LP952L, LP9002S, LP9002DC, LP9002C,
LP9402DC, LP9802, LP982 and LP9802DC PCI host adapters may contain a
laser product known as a small form factor transceiver. This transceiver
provides the physical connection to the optical cable, and its LC−style
connector extends through the mounting bracket. In turn, the host adapter can
be inserted into any host system's appropriate PCI/PCI−X/cPCI/SBus
expansion slot.

In the United States, all optical GLMs, GBICs, 1x9 and small form factor
transceivers sold by Emulex are certified as Class 1 laser products that

Emulex Documentation, Drivers and Software

1

5

Содержание LP9802DC





















Отзывы: