background image

FCC and Regulatory Notices

CLASS 1 LASER PRODUCT
LASER KLASSE 1
LUOKAN 1 LASERLAITE
APPAREIL A` LASER DE CLASSE 1

Model LP9802−F2/LP982−F2/LP9802DC−F2

This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense. Shielded cables
must be used between this equipment and attached peripheral devices. The
reader is cautioned that changes or modifications made to the equipment not
expressly approved by Emulex could void the user's authority to operate this
equipment. The above statement applies to products marketed in the USA

This class A digital apparatus meets all requirements of the Industry Canada
(IC) Interference − Causing Equipment Standard (ICES−003).

Cet appareil numerique de la Classe A respecte toutes les exigences du
reglement sur le materiel brouilleur du Canada.

This statement applies to products marketed in Canada.

Responsible Party: Paul Folino, CEO, Emulex Corporation, 3535 Harbor
Blvd., Costa Mesa, CA 92626, USA, (714) 662−5600

VCCI Notices and Translations (Japan Only)

Note

VCCI regulations provide that changes or modifications not
expressly approved by Emulex Corporation could void your
authority to operate this equipment.

Emulex Documentation, Drivers and Software

12

Содержание LP9802DC





















Отзывы: