background image

Installation

Features

The Emulex LP10000ExDC host bus adapter offers highly integrated 2Gb/s Fibre Channel 

connectivity solutions for enterprise-class storage area networks. The LP10000ExDC is a 

new member of the LP10000 family 

and is 

designed for use with PCI-Express servers. The 

LP10000ExDC HBA delivers state of the art performance through the use of "Thor", 

Emulex’s sixth generation Fibre Channel controller and is a dual channel HBA in a 

standard height, half-length card form factor.

The PCI-Express architecture is an open specification designed to address the wide range 

of current and future system interconnect requirements. It also defines a flexible, scalable, 

high-speed, serial, point-to-point, hot pluggable/hot swappable interconnect that is 

software-compatible with PCI.

The PCI-Express architecture allows the LP10000ExDC to use the same drivers and 

management tools as the LP10000 host bus adapters for PCI and PCI-X systems. 

Emulex’s unique Service Level Interface (SLI) driver architecture, which enables the 

independence of the operating systems device driver from the underlying HBA platform, 

will allow OEMs and end users to migrate to this new system architecture seamlessly 

(without having to change or rewrite drivers utilities and other management tools). 

Emulex’s firmware-based architecture, which allows for new features and other upgrades 

without costly changes to the adapter hardware, provides the kind of technical flexibility 

and investment protection that is critical when working with new and evolving technology.

Major Features

     

Compliant with the PCI-Express 1.0a 

     

x1 or x4 lane link interface at 2.5Gbit/s per lane (auto-negotiated with 

system)

     

Support VC0 (1 Virtual Channel) and TC0 (1 Traffic Class)

     

Configuration / IO / Memory read/write, completion, message 

     

Support 64-bit addressing 

     

32-bit CRC for all transmitted data packets 

     

16-bit CRC on all link message information 

Emulex Documentation, Drivers and Software

2

Содержание LP10000ExDC






















Отзывы: