Emulex LP10000DC Скачать руководство пользователя страница 21

1 x 9 Transceiver

Short wavelength 1x9 transceivers allow normal data transmission on the optical 

link when they are connected to another compatible laser product. Short wavelength 

1x9s embedded in Emulex host adapters are non-OFC. For non-OFC links, a 

compatible laser device must be non-OFC and certified as a Class 1 laser product.

Small Form Factor Transceiver

Short wavelength and long wavelength small form factor transceivers allow normal 

data transmission on the optical link when they are connected to another compatible 

laser product. Short wavelength and long wavelength small form factor transceivers 

embedded in Emulex host adapter are non-OFC. For non-OFC links, a compatible 

laser device must be non-OFC and certified as a Class 1 laser product.

Any system level product that incorporates the small form factor transceivers must 

provide power supply protection that guarantees a voltage of 5.0 volts or less at the 

small form factor transceivers. The functional power supply range of the small form 

factor transceivers product is specified as 3.135 to 3.465V typically. Operation outside 

of this range may degrade the performance and lifetime of the transceiver. The 

transceiver will remain operational with laser emissions below Class 1 limits provided 

the power supply level at the adapter remains at or below 5.0 volts. If the power supply 

level rises above 5.0 volts, the small form factor transceiver cannot be guaranteed to 

operate correctly and could result in laser emissions that may exceed Class 1 limits.

System Level Certification

All GLMs and GBICs sold as accessories by Emulex or host adapters containing 

embedded 1x9 or small form factor transceivers are certified as Class 1 laser products 

within the U.S. and Class 1 laser component assemblies outside of the U.S. 

Manufacturers of products properly incorporating the GLM, GBIC, 1x9 or small form 

factor transceiver do not need to recertify their product for laser safety. The procedure 

for full system certification is therefore identical to that used for any other electronic 

system. When applying for system level certification to electronic standards such as 

IEC950, the regulatory engineers may want to see the DHHS and European conformity 

labeling on the GLM, GBIC, 1x9 or small form factor transceiver, and the system level 

documentation and labeling. Copies of the certificate of conformity for any GLM, GBIC, 

1x9 or small form factor transceiver sold by Emulex can be obtained upon request from 

Emulex Corporation, Costa Mesa.

Emulex Documentation, Drivers and Software

21

Содержание LP10000DC






















Отзывы: