background image

GBIC

The optical GBIC is an integrated duplex data link for bi-directional 

communications over multimode or single mode optical fiber. Each GBIC 

consists of a transmitter and receiver optical subassembly. The transmitter 

subassembly contains a semiconductor laser emitting in the wavelength 

range of 770 to 860 nanometers for shortwave length GBICs and 1270 to 

1355 nanometers for long wavelength GBICs. For non-OFC links, the optical 

power from the laser transmitter is controlled and maintained at a lower 

power level. The power emitted from either an open fiber or open laser 

transmitter is guaranteed to be below the Class 1 limit. Class 1 laser 

products are not considered hazardous. No user maintenance, service 

operations or adjustments can be performed the GBIC. 

Small Form Factor Transceiver

The small form factor transceiver is an integrated duplex data link for bi-

directional communications over multimode or single mode optical fiber. 

Each small form factor transceiver consists of a transmitter and receiver 

optical subassembly. The transmitter subassembly contains a semiconductor 

laser emitting in the wavelength range of 770 to 860 nanometers for 

shortwave length small form factor transceivers and 1270 to 1355 

nanometers for long wavelength small form factor transceivers. For non-OFC 

links, the optical power from the laser transmitter is controlled and 

maintained at a lower power level. The power emitted from either an open 

fiber or open laser transmitter is guaranteed to be below the Class 1 limit. 

Class 1 laser products are not considered hazardous. No user maintenance, 

service operations or adjustments can be performed the small form factor 

transceiver. 

1x9 Transceiver

The 1x9 transceivers is an integrated duplex data link for bi-directional 

communications over multimode fiber. Each 1x9 consists of a transmitter and 

receiver optical subassembly. The transmitter subassembly contains a 

semiconductor laser emitting in the wavelength range of 770 to 860 

nanometers for shortwave 1x9s. For non-OFC links, the optical power from 

the laser transmitter is controlled and maintained at a lower power level. The 

power emitted from either an open fiber or open laser transmitter is 

guaranteed to be below the Class 1 limit. Class 1 laser products are not 

considered hazardous. No user maintenance, service operations or 

adjustments can be performed the 1x9 transceiver.

Emulex Documentation, Drivers and Software

19

Содержание LP10000DC






















Отзывы: