background image

Operating instruction for collet holder  
Type Softsynchro

®

/ PGR

 

 

Edition: 01.04.2012

 

 

3

    

 

®

1  Application range and technical data  

1.1  Application range, determined use 

 
The  collet  holders  type  Softsynchro

®

/PGR  are  used  on  CNC  machining  centres  with 

synchronous control. 
The  integrated  minimal  length  compensation  on  tension  and  compression  compensates 
arising minimal pitch differences between synchronous spindle and tool which would lead to 
high  thread  flank  friction  forces.  An  eventual  increase  of  the  axial  force  during  the  thread 
producing cycle is reduced to a minimum. The resulting advantages are: 

No miscutting of the threads 

Optimised tool life 

 
The  clamping  system  PGR  is  a  mechanical  tool  clamping  system  with  extremely  high 
clamping force and excellent concentricity. The system consists of the tool holder, the high-
precision  collet  and  a  compact  clamping  unit.  The  taper  collet  is  pressed  up  to  the  plane 
contact surface into the tool holder with a force up to 90 kN. The arising press fit creates a 
radial  force  working  on  the  tool  shank  via  the  slotted  collet.  The  tool  is  clamped  safe  and 
centrical. 
 
Normally the collet holders are equipped with one of the following shanks: 

  Cylinder shank acc. to DIN 1835 B+E  

  Hollow taper shank acc. to DIN 69893-HSK-A 

 
The cutting range of each type of tool is indicated in table 1, page 5. 
 
The  tool  is  locked  via  the  collets  type  PGR-GB  (for  tools  with  shank  tolerance  h9  and 
integrated square). The collets  must  be  chosen depending  on their type  and  the tool  used, 
for more information please refer to chapter 

 

2.5.1, page 8. 

 
The collet holders type Softsynchro

®

/PGR are suitable for coolant pressures up to 50 bar.  

 
 

The non-determined use exempts the manufacturer from any liability. 

 

Содержание Softsynchro 1/ PGR

















Отзывы: